Toro Multi Pro 5800 - Installing the Section Manifold Valve; Installing the Valve Actuator

3.Aligntheangeofthemasterboomvalvemanifold,1
gasket,andtheagitationvalvemanifold(BofFigure
98).
4.Assemblethemasterboomvalvemanifold,gasket,and
agitationvalvemanifoldwithaclamptightenedhand
tight(BofFigure98)
5.Aligntheangeofthemasterboomvalvemanifold,1
gasket,andthe90°angedelbow(attheendofthe
hosefortheowmeter;refertoBofFigure98).
6.Assemblethemasterboomvalvemanifold,gasket,and
90°angedelbowwithaclamptightenedhandtight
(BofFigure98).
7.Assembletheagitationvalvetothevalvemountwith
theanged-headboltandangedlocknutthatyou
removedinstep2ofRemovingtheSectionManifold
Valve(page64)andtorquethenutandboltto1017to
1243N-cm(90to110in-lb).
InstallingtheSectionManifoldValve
1.Inserttheupperendcapttingofthemanifoldvalve
intothebypasstting(AofFigure99).
Note:Ifneeded,loosenthemountinghardwarefor
thebypassvalveasneededtoprovideclearance.
Figure99
1.Flange(reducercoupling)6.Socket(outlettting)
2.Socket(bypasstting)
7.Retainer
3.Bypassvalve
8.Flange(manifold—section
valve)
4.Flange(adjacent
manifold—agitationvalve)
9.Gasket
5.Endcaptting(manifold
valveassembly)
10.Flangeclamp
2.Securetheendcapttingtothebypassttingby
insertingaretainerintothesocketofthebypasstting
(AofFigure99).
3.Assembletheoutletttingontothelowerendcap
ttingofthemanifoldvalve(AofFigure99).
4.Securetheendcapttingtotheoutletttingby
insertingaretainerintothesocketoftheoutlettting
(AofFigure99)
5.Aligna1gasketbetweentheangesofthereducer
couplingandthesectionvalvemanifold(BofFigure
99).
6.Assemblethereducercoupling,gasket,andsection
valvemanifoldwithaclamptightenedhandtight(Bof
Figure99).
7.Ifinstallingthe2leftmostsectionvalves,aligna1
gasketbetweentheangesofthe2adjacentsection
valvemanifolds(BofFigure99).
8.Assembletheand2adjacentsectionvalvemanifolds
andgasketwithaclamptightenedhandtight(Bof
Figure99).
9.Fortheleftorrightboomsectionvalves,assemble
thevalvestothevalvemountwiththeanged-head
boltandangedlocknutthatyouremovedinstep3
ofRemovingtheSectionManifoldValve(page64)
andtorquethenutsandboltsto1017to1243N-cm
(90to110in-lb).
10.Ifyouloosenedthemountinghardwareforthebypass
valve,tightenthenutandboltto1017to1243N-cm
(90to110in-lb).
InstallingtheValveActuator
1.Aligntheactuatortothemanifoldvalveand(Figure
82).
2.Securetheactuatorandvalvewiththeretainerthatyou
removedinstep3ofRemovingtheValveActuator
(page61).
3.Connectthe3-pinconnectorofthevalveactuator
harnesstothe3-socketconnectorofthewiringharness
ofthesprayer
69