Toro Reelmaster 3550 - Checking the Reel-To-Bedknife Contact; Checking the Tire Pressure; Torquing the Wheel Nuts; Positioning the Seat

FZG,failstage
11orbetter
Watercontent(newuid)500ppm(maximum)
IndustrySpecications:
VickersI-286-S,VickersM-2950-S,DenisonHF-0,
Vickers35VQ25(EatonATS373-C)
Theproperhydraulicuidsmustbespeciedfor
mobilemachinery(asopposedtoindustrialplantusage),
multiweight-type,withZnDTPorZDDPanti-wearadditive
package(notanashless-typeuid).
Important:Manyhydraulicuidsarealmostcolorless,
makingitdifculttospotleaks.Areddyeadditivefor
thehydraulicsystemuidisavailablein20ml(2/3oz)
bottles.Onebottleissufcientfor15to22L(4to6US
gallons)ofhydraulicuid.OrderPartNo.44-2500from
yourauthorizedTorodistributor.
Synthetic,BiodegradableHydraulicFluidisavailablein
19L(5gallon)containersor208L(55gallon)drums—see
thepartsdocumentationoryourTorodistributorforpart
numbers.
Thishigh-quality,synthetic,biodegradableuidhasbeen
testedandfoundcompatibleforthisToromodel.Other
brandsofsyntheticuidmayhavesealcompatibilityproblems
andTorocannotassumeresponsibilityforunauthorized
substitutions.
Note:Thissyntheticuidisnotcompatiblewiththe
ToroBiodegradableFluidpreviouslysold.SeeyourToro
distributorformoreinformation.
Alternativeuids:
•MobilEALEnvirosynH46(US)
•MobilEALHydraulicOil46(international)
1.Parkthemachineonalevelsurface,lowerthecutting
units,engagetheparkingbrake,shutofftheengine,
andremovethekey.
2.Cleantheareaaroundthellerneckandcapofthe
hydraulictank(Figure30).Removethecap.
g008886
Figure30
1.Hydraulic-tankcap
3.Removethedipstickfromthellerneckandwipeit
withacleanrag.Insertthedipstickintothellerneck;
thenremoveitandchecktheuidlevel.Theuidlevel
shouldbewithin6mm(1/4inch)ofthemarkonthe
dipstick.
4.Ifthelevelislow,addtheappropriateuidtoraisethe
leveltotheFullmark.
5.Installthedipstickandcapontothellerneck.
CheckingtheReel-to-Bedknife
Contact
Eachdaybeforeoperating,checkthereel-to-bedknifecontact,
regardlessofwhetherthequalityofcuthadpreviouslybeen
acceptable.Theremustbelightcontactacrossthefulllength
ofthereelandthebedknife(refertoAdjustingtheReelto
BedknifeinthecuttingunitOperator'sManual).
CheckingtheTirePressure
ServiceInterval:Beforeeachuseordaily
Thetiresareover-inatedforshipping.Therefore,release
someoftheairtoreducethepressure.Thecorrectair
pressureinthetiresis83kPa(12psi).
Note:Maintaintherecommendedpressureinalltiresto
ensureagoodqualityofcutandpropermachineperformance.
DANGER
Lowtirepressuredecreasesmachinesidehill
stability.Thiscouldcausearollover,whichmay
resultinpersonalinjuryordeath.
Donotunder-inatethetires.
TorquingtheWheelNuts
ServiceInterval:Afterthersthour
Aftertherst10hours
Every200hours
Torquethewheelnutsto61to88N∙m(45to65ft-lb).
WARNING
Failuretomaintainpropertorqueofthewheelnuts
couldresultinpersonalinjury.
Maintainpropertorqueofthewheelnuts.
PositioningtheSeat
ChangingtheSeatPosition
Theseatcanmoveforwardandbackward.Positiontheseat
whereyouhavethebestcontrolofthemachineandaremost
comfortable.
1.Movetheleversidewaystounlocktheseat(Figure31).
22