Toro Reelmaster 5410-D

To Next Page

To Previous Page

decal145-2483

145-2483

1.Parkingbrake

5.PTO—Disengage

2.Cruisecontrol6.PTO—Engage

3.Lowerthecuttingunits.

7.ReadtheOperator’s

Manual.

4.Raisethecuttingunits.

Main Page

Table of Contents3
Safety4
General Safety4
Safety and Instructional Decals5
Setup10
Preparing the Machine11
Adjusting the Control-Arm Position11
Installing the Cutting Units11
Using the Cutting-Unit Kickstand19
Installing the CE Hood Lock19
Applying the CE Decals20
Product Overview21
Controls21
Seat Controls23
Specifications25
Attachments/Accessories25
Before Operation25
Before Operation Safety25
Performing Daily Maintenance26
Filling the Fuel Tank26
Checking the Interlock Switches27
Using the Infocenter LCD Display28
Using the Menus29
Protected Menus31
Checking the Hydrostatic Braking Distance33
Understanding Reverse Speeds33
Understanding Displayed Traction Speeds33
During Operation33
During Operation Safety33
Understanding the Operating Characteristics of the Machine35
Operating the Machine35
Using the Traction Pedal35
Using the Virtual Pedal Stop (VPS) Feature36
Operating the Cruise Control36
Understanding the Acceleration Mode37
Understanding the Warm-Up Mode37
Understanding Toro Smart Power37
Starting the Engine38
Shutting off the Engine38
Cutting Grass with the Machine38
Diesel Particulate Filter Regeneration38
Adjusting the Turf-Compensation Spring51
Adjusting the Lift-Arm Counterbalance51
Adjusting the Lift-Arm Turnaround Position52
Setting the Reel Speed53
Understanding the Diagnostic Light54
Operating Tips54
After Operation55
After Operation Safety55
Identifying the Tie-Down Points55
Hauling the Machine56
Pushing or Towing the Machine56
Maintenance58
Maintenance Safety58
Recommended Maintenance Schedule(S)58
Daily Maintenance Checklist60
Pre-Maintenance Procedures61
Preparing for Maintenance61
Opening the Hood61
Closing the Hood61
Opening the Screen61
Closing the Screen62
Tilting the Seat62
Lowering the Seat62
Jacking Point Locations62
Lubrication63
Greasing the Bearings and Bushings63
Engine Maintenance64
Engine Safety64
Checking the Air Filter64
Servicing the Air Cleaner65
Resetting the Air Filter Service Indicator66
Servicing the Engine Oil66
Fuel System Maintenance68
Fuel Maintenance68
Storing Fuel68
Servicing the Fuel-Water Separator68
Servicing the Fuel Filter69
Draining the Fuel Tank69
(Figure 116)69
Figure 12069
Close and Latch the Hood; Refer to69
Closing the Hood69
Inspecting the Fuel Lines and Connections70
Servicing the Diesel-Oxidation Catalyst (DOC) and the Soot Filter70
Cleaning the Fuel-Pickup Tube Screen70
Priming the Fuel System73
Electrical System Maintenance73
Electrical System Safety73
Disconnecting the 12 V Battery73
Connecting the 12 V Battery74
Charging the 12 V Battery74
Servicing the 12 V Battery74
Prepare the Machine for Maintenance; Refer to Preparing for Maintenance74
Replacing a 12 V Fuse-Block Fuse75
Replacing the TEC Fuse75
Replacing the ECU Fuse76
Drive System Maintenance77
Checking the Tire Air Pressure77
Checking the Torque of the Wheel Nuts77
Checking the Rear-Wheel Alignment77
Adjusting the Rear Wheel Toe-In77
Cooling System Maintenance78
Cooling System Safety78
Coolant Specification78
Checking the Coolant Level79
Removing Debris from the Cooling System79
Open the Hood; Refer to Opening the Hood79
Figure 14179
Belt Maintenance81
Servicing the Alternator Belt81
Hydraulic System Maintenance81
Hydraulic System Safety81
Hydraulic Fluid Specifications81
Checking the Hydraulic-Fluid Level82
Checking the Hydraulic Lines and Hoses82
Hydraulic Fluid Capacity82
Changing the Hydraulic Fluid82
Replacing the Hydraulic Filters83
Cutting Unit Maintenance85
Blade Safety85
Checking the Reel-To-Bedknife Contact85
Backlapping the Cutting Units85
Chassis Maintenance87
Inspecting the Seat Belt87
Extended Maintenance87
Chassis and Engine87
Cleaning88
Washing the Machine88
Storage88
Storage Safety88
Preparing the Traction Unit88
Preparing the Engine89
Storing the Battery89

Toro Reelmaster 5410-D - Page 7

Table of Contents

Related product manuals