Why is the printed image blurred on my Toshiba B-EX6T1?
If the printed image from your Toshiba Barcode Reader is blurred, the combination of the ribbon and media might not be correct, or the print head might be dirty. Select an appropriate ribbon for the media type being used. Clean the print head using the Print Head Cleaner or a cotton swab slightly moistened with ethyl alcohol.
What to do if Toshiba B-EX6T1 shows HEAD OPEN error?
The 'HEAD OPEN' error on your Toshiba Barcode Reader means the Print Head Block is open. If the Print Head Block is opened in Online mode, or if feeding or printing has been attempted with the Print Head Block open, close the Print Head Block. If feeding or printing was attempted, press the [RESTART] key after closing it.
What does SYSTEM ERROR mean on my Toshiba B-EX6T1?
A 'SYSTEM ERROR' on your Toshiba Barcode Reader can be caused by several factors. The printer might be in a noisy location, the power cord may not be grounded, it could be sharing a power source, or there might be an issue with the application software on your host computer. Keep the printer and interface cables away from noise sources. Ensure the power cord is grounded and provide an exclusive power source for the printer. Confirm that the host computer operates properly.
Why is my Toshiba Barcode Reader printing nothing on the media?
If your Toshiba Barcode Reader is printing nothing on the media, it could be due to several reasons. The media or ribbon may not be loaded properly, the print head might not be installed correctly, or the combination of ribbon and media may be incorrect. Load the media and ribbon properly. Ensure the print head is correctly installed and the Print Head Block is closed. Select an appropriate ribbon for the media type being used.
How to troubleshoot a Toshiba Barcode Reader that will not turn on?
If your Toshiba Barcode Reader won't turn on, the power cord may be disconnected, the AC outlet might not be working, or the fuse could be blown. First, plug in the power cord. If that doesn't work, test the AC outlet with another electrical appliance. Finally, check the fuse or circuit breaker.
Why does my Toshiba B-EX6T1 show a COMMS ERROR?
A 'COMMS ERROR' on your Toshiba Barcode Reader indicates a communication issue. Ensure the interface cable is correctly connected to both the printer and the host, and verify that the host is turned on.
How to fix NO PAPER error on Toshiba B-EX6T1?
If your Toshiba Barcode Reader shows a 'NO PAPER' error, it could be due to a few reasons: the media has run out, it's not loaded correctly, the sensor position needs adjustment, the sensor isn't calibrated, or the media is slack. First, load new media or reload it correctly, and then press the [RESTART] key. If that doesn't work, adjust the sensor position and take up any slack in the media.
What does SYNTAX ERROR mean on Toshiba B-EX6T1?
A 'SYNTAX ERROR' on your Toshiba Barcode Reader means that while the printer is in Download mode for upgrading the firmware, it received an improper command. Turn the printer off, and then on again.
What causes RIBBON ERROR on Toshiba B-EX6T1?
A 'RIBBON ERROR' on your Toshiba Barcode Reader can occur if the ribbon is not fed or loaded properly, or if the ribbon sensor has a problem. Remove the ribbon and check its status, replacing it if necessary. If the problem persists, turn off the printer and contact an authorized service representative.
General| Type | Industrial Barcode Printer |
|---|---|
| Print Method | Thermal Transfer / Direct Thermal |
| Operating Temperature | 5°C to 40°C |
| Storage Temperature | -20°C to 60°C |
| Power Supply | 100-240 VAC, 50/60 Hz |
| Compliance | CE, FCC, RoHS |
| Resolution | 300 dpi |
| Interfaces | USB, Serial, Ethernet |
Describes the capabilities and supported operating systems of the printer driver.
Lists all TOSHIBA Bar Code Printer models supported by this driver.
Explains formatting conventions like brackets, quotes, and bold/italic for menu items, messages, and titles.
States that screens shown are examples, primarily based on Windows XP, and may differ.
Lists trademark acknowledgments and abbreviations for operating systems.
Details the system requirements and operational conditions for using the printer driver.
Provides important warnings and notes regarding driver installation and version compatibility.
Outlines common preparatory steps before installing the printer driver.
Details the steps to download and prepare the printer driver installation file.
Guides through installing the driver on older Windows operating systems.
Explains the installation process for modern Windows operating systems.
Details the USB installation procedure for Windows 2000 with Plug & Play.
Guides through USB installation on Windows XP/Server2003 with Plug & Play.
Covers USB installation on newer Windows versions with Plug & Play enabled.
Details parallel interface installation for Windows 2000 with Plug & Play.
Guides through parallel interface installation on Windows XP/Server2003 with Plug & Play.
Covers parallel interface installation on newer Windows versions with Plug & Play.
Provides instructions on how to remove the printer driver software from the system.
Details the procedure for uninstalling most printer driver versions.
Specific instructions for uninstalling older driver versions V6.5 Build75 and V6.5 Build77.
Allows specifying media size, orientation, and other properties of the media.
Enables adjustment of dithering or color tone for print quality.
Sets print conditions like media settings, issue settings, and fine adjustments.
Configures graphic options, print density, and feed adjustments.
Manages bar code fonts, enabling adding, deleting, and modifying them.
Enables testing printer operations and setting variable options.
Explains how to use resident fonts and bar code symbologies in Windows applications.
Provides examples of direct and network printer connections.
Step-by-step guide to adding a new Standard TCP/IP printer port.
Instructions on how to remove an existing Standard TCP/IP printer port.
Explains how to enable or disable the bi-directional communication feature for the printer.
Provides a procedure for setting printer parameters like Centro Mode and Plug & Play.
Details how to connect the printer to a network using different LAN interfaces and methods.
To Next Page
