© 2003 - 2008 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO350/352/353/450/452/453
ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 5
2
E9F0 Finisher jam (Puncher
unit)
Punching jam: Punching is not performed properly.
[MJ-1023/1024 (when MJ-6004 is installed)]
[MJ-1101 (when MJ-6101 is installed)]
P. 5 - 5 0
EA10 Finisher jam (Finisher
unit)
Paper transport delay jam: The paper which has
passed the bridge unit does not reach the inlet sen-
sor. [MJ-1022/1023/1024/1101]
P. 5 - 3 3
EA20 Paper transport stop jam:
(1) The paper does not pass through the inlet sen-
sor. [MJ-1022/1023/1024]
(2) The paper has passed through the inlet sensor
but does not reach or pass the feed path sensor or
processing tray sensor. [MJ-1023/1024]
(3) The paper which has passed through the inlet
sensor does not reach the transport sensor. [MJ-
1101]
P. 5 - 3 5
EA21 Paper size error jam: Paper does not reach the sen-
sor because the paper is shorter than spec. [MJ-
1101]
P. 5 - 3 6
EA30 Power-ON jam:
(1) Paper exists at the inlet sensor when power is
turned ON. [MJ-1022/1023/1024]
(2) Paper exists at the feed path sensor or process-
ing tray sensor when power is turned ON.
[MJ-1023/1024]
P. 5 - 3 7
EA31 Transport path paper remaining jam: The paper
which has passed through the inlet sensor does not
reach the transport sensor. [MJ-1101]
P. 5 - 3 8
EA32 Exit paper remaining jam: The paper is remaining
on the finishing tray when the power is turned ON.
[MJ-1101]
P. 5 - 3 8
EA40 Door open jam:
(1) The finisher has been released from the equip-
ment during printing. [MJ-1022]
(2) The upper/front cover of the finisher unit or the
upper/front door of the puncher unit has opened
during printing. [MJ-1023/1024]
(3) The front cover or stationary tray cover is
opened during paper transport. [MJ-1101]
P. 5 - 3 9
EA50 Stapling jam: Stapling is not performed prop-
erly.[MJ-1022/1023/1024/1101]
P. 5 - 4 2
EA60 Early arrival jam: The inlet sensor detects the paper
earlier than a specified timing. [MJ-1022/1023/
1024/1101]
P. 5 - 4 4
EA70 Stack delivery jam: It cannot deliver the stack of
paper on the intermediary process tray to the stack
tray. [MJ-1022]
P. 5 - 4 5
Stack exit belt home position error: The stack exit
belt is not at the home position. [MJ-1101]
EA80 Finisher jam (Saddle
stitcher unit)
Stapling jam: Stapling is not performed properly.
[MJ-1024]
P. 5 - 4 7
EA90 Door open jam: The delivery cover or the inlet cover
has opened during printing [MJ-1024].
P. 5 - 4 7
EAA0 Power-ON jam: Paper exists at No.1 paper sensor,
No. 2 paper sensor, No.3 paper sensor, vertical
path paper sensor or delivery sensor when power is
turned ON. [MJ-1024]
P. 5 - 4 8
Error code Classification Contents Troubleshooting
06/01
To Next Page
Loading...
