How to reduce high pressure discomfort with Transcend Micro Medical Equipment?
If you experience discomfort due to a feeling of high pressure with your Transcend Medical Equipment, try breathing slowly through your nose with your mouth closed. If available, use the ramp pressure feature. This issue may arise if the device pressure is set too high. If the problem continues, it's best to contact your homecare provider for assistance.
What to do if the Transcend Micro Medical Equipment control panel LEDs don't flash?
If the control panel LEDs on your Transcend Medical Equipment don't flash or illuminate when connected to a power supply, first check all power connections to ensure they are properly connected. Also, verify if the LED light on the power supply itself is illuminated. If the connections are good, try using another power outlet, making sure it is not controlled by a wall switch.
How to fix dry nose or throat irritation with Transcend Micro Medical Equipment?
If you are experiencing dry nose or throat irritation while using your Transcend Medical Equipment, it could be due to dry air or a dirty air path accessory or filter. You can try the following: * Add humidity to the room. * Replace the HME if you're using one and ensure the Transcend AirMist HME is secure. * Follow the cleaning instructions for your accessories. * Change the air filter. If the problem persists, contact your homecare provider.
What to do if Transcend Micro shuts down during therapy?
If your Transcend Medical Equipment shuts down during therapy, it might be due to an improper seal of the external hardware, such as the mask or tubing, or the use of external hardware past its recommended service life. To address this, verify that all external equipment in the breathing circuit is correctly seated to ensure a proper seal. Also, check the hose for leaks and follow the mask manufacturer's recommendations for fit and seal.
Why is there low mask pressure with Transcend Medical Equipment?
If you experience discomfort due to a feeling of low pressure in your mask while using Transcend Medical Equipment, it could be due to the device being set too low or excessive leaks around the hose or mask. Contact your home care provider for a setting change. Also, check the hose, mask, and any accessories in the breathing circuit for air leaks and ensure they fit properly.
How to prevent water droplets in mask with Transcend Micro Medical Equipment?
If you notice droplets of water in your mask after using your Transcend Medical Equipment, it's likely due to excess condensation from breathing. To resolve this, run the drying mode after therapy. Additionally, try using the equipment in a less humid environment, perhaps with a dehumidifier.
What does it mean when all LEDs flash two times on Transcend Micro Medical Equipment?
If all the LEDs on your Transcend Medical Equipment flash two times, pause, and then flash again, it indicates that the device has detected an operating error. To resolve this, hold down the power button until all LEDs stop flashing. Then, release the power button, and the device will reset and power up in Standby Mode. Ensure you also check the hose, mask, and any accessories in the breathing circuit for air leaks and proper fit. If the problem persists, contact your homecare provider.
What does it mean when all LEDs flash four times on Transcend Micro Medical Equipment?
If all the LEDs on your Transcend Medical Equipment flash four times, pause, and then flash again, it means the device has detected an operating error. To fix this, hold down the power button until all LEDs stop flashing. Release the power button, and the device will reset and power up in Standby Mode. If the LEDs begin to flash again, contact your homecare provider.
Why is SleepStart not working on my Transcend Micro?
If SleepStart is not functioning with your Transcend Medical Equipment, it could be due to excessive leaks in the breathing circuit or the user not breathing deeply enough to trigger SleepStart. Check the hose, mask, and any accessories in the breathing circuit for air leaks and ensure they fit properly. Also, make sure to take a deep breath with the mask securely fitted, or press the Power button to start therapy. If the problem persists, call your homecare provider’s technical service department.
What to do if there is no airflow from Transcend Medical Equipment?
If your Transcend Medical Equipment has no airflow, it indicates a device motor failure or electronics failure. Contact the homecare provider’s technical service department.
General| Brand | Transcend |
|---|---|
| Product | Micro |
| Pressure Range | 4-20 cmH2O |
| Altitude Adjustment | Automatic |
| Operating Modes | CPAP |
To Next Page
