Why don't the mower decks follow contours on my Trimax Measuring Instruments?
If the mower decks on your Trimax Measuring Instruments aren't following contours, ensure the auxiliary hydraulic valve is in the float position by using the correct auxiliary hydraulic circuit. If no float position is available, hold the hydraulic lever in the down position while the mower decks traverse dips.
Why do the mower deck skids mark turf on my Trimax Measuring Instruments?
If the mower deck skids are marking the turf with your Trimax Measuring Instruments, it could be because the ground contours are too extreme for the mower. Try changing the mowing pattern to approach contours from a different angle. Also, check if the wear skids are too low and adjust them accordingly.
Why do blades leave a scalloped pattern on the turf when using my Trimax SnakeS2 Measuring Instruments?
A scalloped pattern on the turf from your Trimax Measuring Instruments blades can be due to travel speed being too fast; select a lower gear and travel more slowly. It could also be caused by mower decks bouncing; consider fitting optional wear skids.
Why do roller or spindle bearings fail on Trimax SnakeS2 Measuring Instruments?
Roller or spindle bearing failures in Trimax Measuring Instruments can be caused by water in the bearings. Avoid directing hoses or pressure washers at the bearings.
Why does the primary driveshaft CV joint break on my Trimax SnakeS2 Measuring Instruments?
If the primary driveshaft CV joint breaks on your Trimax Measuring Instruments, it is likely because the driveshaft angle exceeds 80°. Limit turn angles, especially when reversing, to prevent this.
Why is there a poor cut or spread on side decks only of my Trimax SnakeS2 Measuring Instruments?
If you're experiencing a poor cut or spread on the side decks only of your Trimax Measuring Instruments, the blades may be turning backwards. This can happen if the chassis gearbox is fitted incorrectly. Un-bolt the gearbox and rotate it 180 degrees to correct this.
Identifies potential hazards associated with the mower and provides remedies.
Explains the importance and proper application of safety labels on the equipment.
Emphasizes the owner's responsibility for training and safe operation.
Details the requirement for operators to understand manual information.
Provides a form for documenting operator training and comprehension.
Details the meaning and significance of various safety and warning labels.
Details the procedure for connecting the mower to the tractor drawbar.
Details the procedure to remove air from hydraulic lift rams.
Lists additional checks before operation, like lights and driveshaft angles.
Provides steps for safely disconnecting the mower from the tractor.
Outlines essential daily checks to ensure safe and reliable mower operation.
Explains the function and configuration of transport locks for securing mower decks.
Details how to raise and lower mower decks using the standard pull rope.
Explains raising and lowering decks with the optional remote unlock system.
Describes the kerb jump function for momentary deck lifting.
Explains how to adjust the mower's cutting height using roller position.
Provides safety and preparation steps for transporting the mower.
Outlines safety precautions and steps for starting the mower for operation.
Offers advice and tips for optimal mower operation and performance.
Details how to access, inspect, and maintain transmission covers.
Explains checking and replacing drive belts, emphasizing genuine parts.
Covers safety and procedures for inspecting, replacing, and maintaining mower blades.
Guides on fitting and adjusting optional roller scrapers.
Explains the purpose and fitting of optional wear skids.
Provides instructions for proper greasing of various mower components.
Details how to check and change gearbox oil levels.
Covers regular maintenance and servicing of the mower driveshafts.
Details tyre pressure checks and wheel removal/replacement procedures.
Explains the need to check roll and pitch pivots for tightness periodically.
Provides instructions on how to clear blockages in the cutting chamber.
Details proper procedures for cleaning the mower after use.
Covers checking and maintaining the mower's roller bearings.
Provides specific instructions and diagrams for lifting and securing the mower.
General| Brand | Trimax |
|---|---|
| Model | SnakeS2 |
| Category | Measuring Instruments |
| Language | English |
To Next Page