What does ‘Low Heat’ mean on my Tuttnauer 2340EA Laboratory Equipment?
If the message ‘Low Heat’ is displayed during heat up on your Tuttnauer Laboratory Equipment, it indicates a bad temperature sensor. If heating elements are remaining on instead of cycling on and off, call for a technician.
How to clean a very dirty chamber in my Tuttnauer Laboratory Equipment?
If the chamber of your Tuttnauer Laboratory Equipment is very dirty, use Chamber Brite ™ to clean the autoclave; very dirty machines may require two cleanings.
What to do if Tuttnauer 2340EA process fails during heating stage with a HIGH TEMP message?
If your Tuttnauer Laboratory Equipment process fails while initiating the heating stage and displays a HIGH TEMP message, try changing the setting of the thermostat.
How to troubleshoot Tuttnauer 2340EA machine not responding?
If your Tuttnauer Laboratory Equipment machine isn't responding, verify that the main switch is in the ‘On’ position, the power cord is properly connected to both the machine and the mains, and the circuit breaker hasn't tripped. Also, check the reset button on the cut-out thermostat.
What should I do if my Tuttnauer 2340EA shows ‘Low Pres’?
If the 'Low Pres' message is displayed on your Tuttnauer Laboratory Equipment, clean the water level electrode inside the vessel. Also, ensure the door is fully closed, the door gasket is properly seated, and there is no steam leakage. Check the leveling of the machine.
How to fix ‘High Pres’ error on Tuttnauer Laboratory Equipment?
If the 'High Pres' message appears on your Tuttnauer Laboratory Equipment, the air jet might be clogged; clean it. It could also mean that the heating elements are continuously on, or the temperature sensor is faulty. In these cases, contact a technician.
How to unclog the drain on Tuttnauer 2340EA Laboratory Equipment?
If the drain of your Tuttnauer Laboratory Equipment is clogged: 1. Open the drain by turning it counterclockwise and place a heavy object over the reservoir cover. 2. Blow compressed air into the drain to force debris back into the reservoir, then clean out the reservoir. 3. Alternatively, disassemble the drain valve, clean it, and blow out the line. Reassemble the valve, ensuring the large 'O' ring is properly seated.
What should I do if my Tuttnauer Laboratory Equipment displays ‘High Pres’?
If your Tuttnauer Laboratory Equipment displays ‘High Pres’, clean the air jet. Ensure the sterilization time and temperature are set correctly; if unsure, use the default settings. Also, make sure the autoclave is not too heavily loaded.
What to do if my Tuttnauer 2340EA is not responding?
If your Tuttnauer Laboratory Equipment is not responding, ensure the main switch is in the ‘On’ position. Also, verify the power cord is properly connected to both the machine and the mains. Check the reset button on the cut-out thermostat and make sure the circuit breaker hasn't tripped; lift the circuit breaker lever if it has.
Why is my Tuttnauer Laboratory Equipment leaking at the door?
If your Tuttnauer Laboratory Equipment is leaking at the door, ensure the door is tightened enough and the door gasket is sealing the chamber. If necessary, replace the door gasket.
Explains common error messages, warning messages, and associated safety measures.
Details the four sterilization programs, their settings, and operational sequences.
Covers electrical connection requirements, safety, and compliance with regulations.
Details the crucial chamber pitch adjustment for older units and its impact on operation.
Instructions on cleaning, rinsing, and drying instruments before sterilization.
Guidance on packaging methods, tray placement, and preventing issues like water accumulation.
Advice on handling specific materials, preventing cross-contamination, and ensuring proper exposure.
Steps before starting operation, including water filling, power connection, and program selection.
How to start a cycle, monitor its progress, and understand indicator lights.
Outlines daily, weekly, and periodic maintenance tasks for optimal performance.
Solutions for unresponsive machines and 'Low Heat' error messages.
Troubleshooting for 'Low Water' and 'Low Pres' messages, including door seal checks.
Addresses 'Low Temp'/'High Temp' errors and common printer operational issues.
General| Type | Autoclave |
|---|---|
| Power | 1200 W |
| Frequency | 50/60 Hz |
| Chamber Material | Stainless Steel |
| Sterilization Time Range | 3 - 30 minutes |
| Warranty | 1 year |
| Cycle Time | 30 minutes |
| Sterilization Temperature Range | 121°C to 134°C |
To Next Page
