What does ‘Low Heat’ mean on my Tuttnauer 2540EA?
If the message ‘Low Heat’ is displayed during heat up on your Tuttnauer Laboratory Equipment, it indicates a bad temperature sensor. If heating elements are remaining on instead of cycling on and off, call for a technician.
How to clean a very dirty chamber in my Tuttnauer 2540EA?
If the chamber of your Tuttnauer Laboratory Equipment is very dirty, use Chamber Brite ™ to clean the autoclave; very dirty machines may require two cleanings.
What to do if Tuttnauer 2540EA process fails during heating stage with a HIGH TEMP message?
If your Tuttnauer Laboratory Equipment process fails while initiating the heating stage and displays a HIGH TEMP message, try changing the setting of the thermostat.
How to troubleshoot Tuttnauer Laboratory Equipment machine not responding?
If your Tuttnauer Laboratory Equipment machine isn't responding, verify that the main switch is in the ‘On’ position, the power cord is properly connected to both the machine and the mains, and the circuit breaker hasn't tripped. Also, check the reset button on the cut-out thermostat.
What should I do if my Tuttnauer 2540EA Laboratory Equipment shows ‘Low Pres’?
If the 'Low Pres' message is displayed on your Tuttnauer Laboratory Equipment, clean the water level electrode inside the vessel. Also, ensure the door is fully closed, the door gasket is properly seated, and there is no steam leakage. Check the leveling of the machine.
How to fix ‘High Pres’ error on Tuttnauer 2540EA Laboratory Equipment?
If the 'High Pres' message appears on your Tuttnauer Laboratory Equipment, the air jet might be clogged; clean it. It could also mean that the heating elements are continuously on, or the temperature sensor is faulty. In these cases, contact a technician.
How to unclog the drain on Tuttnauer 2540EA?
If the drain of your Tuttnauer Laboratory Equipment is clogged: 1. Open the drain by turning it counterclockwise and place a heavy object over the reservoir cover. 2. Blow compressed air into the drain to force debris back into the reservoir, then clean out the reservoir. 3. Alternatively, disassemble the drain valve, clean it, and blow out the line. Reassemble the valve, ensuring the large 'O' ring is properly seated.
What should I do if my Tuttnauer Laboratory Equipment displays ‘High Pres’?
If your Tuttnauer Laboratory Equipment displays ‘High Pres’, clean the air jet. Ensure the sterilization time and temperature are set correctly; if unsure, use the default settings. Also, make sure the autoclave is not too heavily loaded.
What to do if my Tuttnauer Laboratory Equipment is not responding?
If your Tuttnauer Laboratory Equipment is not responding, ensure the main switch is in the ‘On’ position. Also, verify the power cord is properly connected to both the machine and the mains. Check the reset button on the cut-out thermostat and make sure the circuit breaker hasn't tripped; lift the circuit breaker lever if it has.
Why is my Tuttnauer 2540EA leaking at the door?
If your Tuttnauer Laboratory Equipment is leaking at the door, ensure the door is tightened enough and the door gasket is sealing the chamber. If necessary, replace the door gasket.
Inspect the autoclave for damage upon arrival and verify packing integrity.
Provides detailed electrical specifications, including voltage, amperage, and fuse ratings.
Presents overall dimensions, weight, and other physical characteristics of the autoclave models.
Lists chamber dimensions, water reservoir capacity, tray sizes, and shipping details.
Detailed explanation of program keys and other control buttons on the autoclave interface.
Explains common messages, error codes, and safety measures displayed by the autoclave.
Details the settings and sequence for sterilizing unwrapped instruments.
Outlines the parameters for sterilizing wrapped instruments and porous materials.
Specifies the cycle for sterilizing glassware with slow exhaust and no drying.
Describes the program used for an additional drying cycle for specific items.
Guides on proper electrical connection, safety, and compliance with regulations.
Procedures for setting and checking the automatic water filling system.
Covers daily, weekly, and periodic maintenance tasks for optimal device performance.
General| Type | Automatic Autoclave |
|---|---|
| Voltage | 120V or 230V |
| Frequency | 50/60 Hz |
| Power | 1400W |
| Door Type | Manual |
| Number of Trays | 2 |
| Safety Features | automatic shut off at the end of both sterilization and drying cycles, Overheat cut-off, automatic shut off at the end of both sterilization and drying cycles, insufficient water level sensor |
To Next Page
