What to do if Tuttnauer 3140EA chamber is not filling?
If your Tuttnauer Laboratory Equipment chamber is not filling, check the water level in the reservoir and for any obstructions blocking the pickup tube. Clean the water sensor and try filling the machine manually using the Manual Inlet key.
What to do when my Tuttnauer 3140EA displays ‘High Temp’?
If your Tuttnauer Laboratory Equipment displays ‘High Temp’, clean the air jet and check for proper voltage at the wall outlet.
What does ‘Low Heat’ mean on my Tuttnauer 3140EA Laboratory Equipment?
If the message ‘Low Heat’ is displayed during heat up on your Tuttnauer Laboratory Equipment, it indicates a bad temperature sensor. If heating elements are remaining on instead of cycling on and off, call for a technician.
How to clean a very dirty chamber in my Tuttnauer 3140EA?
If the chamber of your Tuttnauer Laboratory Equipment is very dirty, use Chamber Brite ™ to clean the autoclave; very dirty machines may require two cleanings.
What to do if Tuttnauer 3140EA keyboard does not respond?
If the keyboard on your Tuttnauer Laboratory Equipment does not respond, press the STOP key for 2 seconds to abort any program that may still be running.
Why is my Tuttnauer 3140EA making a loud noise?
If you hear a loud noise coming from the reservoir of your Tuttnauer Laboratory Equipment, the sterilization temperature may be set too high. The maximum setting is 274ºF (134ºC).
What to do if Tuttnauer Laboratory Equipment displays ‘Low Water’?
If the 'Low Water' message is displayed on your Tuttnauer Laboratory Equipment, clean the water level electrode inside the vessel. Also, ensure the door is fully closed with the gasket properly seated, and check that the machine is level. Replace the door gasket if there's any steam leakage.
Why does my Tuttnauer 3140EA display ‘Low Temp’?
If the 'Low Temp' message appears on your Tuttnauer Laboratory Equipment, refer to the solutions for the Low Water problem. Additionally, check if the sterilization time is set too long, causing the chamber to run dry.
How to fix a Tuttnauer Laboratory Equipment chamber that is not filling?
If the chamber of your Tuttnauer Laboratory Equipment is not filling, check the water level in the reservoir. Also, inspect the bottom of the reservoir for any obstruction blocking the pickup tube. Clean the water sensor and try filling the machine manually using the Manual Inlet key.
What to do if my Tuttnauer 3140EA Laboratory Equipment is not responding?
If your Tuttnauer Laboratory Equipment is not responding, ensure the main switch is in the ‘On’ position. Also, verify the power cord is properly connected to both the machine and the mains. Check the reset button on the cut-out thermostat and make sure the circuit breaker hasn't tripped; lift the circuit breaker lever if it has.
Inspect the autoclave's exterior and interior for damage upon arrival. Document any issues.
Table detailing electrical specifications, fuses, and circuit breakers for different models.
Comprehensive table of model specifications including chamber size, water volume, tray dimensions, and weight.
Detailed explanation of the program keys and other operational buttons on the control panel.
Explains common error messages, their causes, and corresponding safety measures.
Details nominal parameters and operational sequence for sterilizing unwrapped instruments.
Provides settings and sequence for sterilizing wrapped items and porous loads with drying.
Overview of daily, weekly, and periodic maintenance tasks to keep the autoclave in good working condition.
Instructions for cleaning the air jet located in the water reservoir to prevent spore test failures.
Step-by-step guide for using Chamber Brite cleaner to descale and clean the autoclave.
Troubleshooting steps for unresponsive machines and initial error displays like 'Low Heat', 'Low Water', 'Low Pres', 'Low Temp'.
Resolving 'High Temp', 'High Pres' errors, printer malfunctions, and continuous paper feed issues.
Addressing door leaks, long exhaust stages, and blocked water outlet strainers.
Troubleshooting clogged drains, failed spore tests, wet or burned items, and instrument rusting.
Resolving keyboard unresponsiveness, slow heat-up, noise, long drying times, and chamber filling problems.
General| Model | 3140EA |
|---|---|
| Type | Autoclave |
| Chamber Material | Stainless Steel |
| Power Supply | 50/60Hz |
| Operating Pressure | 2.1 Bar |
| Temperature Range | 105°C to 138°C |
To Next Page