Why is my Tuttnauer 3140EA leaking at the door?
If your Tuttnauer Laboratory Equipment is leaking at the door, ensure the door is tightened enough and the door gasket is sealing the chamber. If necessary, replace the door gasket.
What to do if my Tuttnauer 3140EA Laboratory Equipment is not responding?
If your Tuttnauer Laboratory Equipment is not responding, ensure the main switch is in the ‘On’ position. Also, verify the power cord is properly connected to both the machine and the mains. Check the reset button on the cut-out thermostat and make sure the circuit breaker hasn't tripped; lift the circuit breaker lever if it has.
How to clean a very dirty Tuttnauer Laboratory Equipment chamber?
To clean a very dirty chamber in your Tuttnauer Laboratory Equipment, use Chamber Brite ™. Very dirty machines may require two cleanings.
How to unclog the drain on Tuttnauer 3140EA Laboratory Equipment?
If the drain of your Tuttnauer Laboratory Equipment is clogged: 1. Open the drain by turning it counterclockwise and place a heavy object over the reservoir cover. 2. Blow compressed air into the drain to force debris back into the reservoir, then clean out the reservoir. 3. Alternatively, disassemble the drain valve, clean it, and blow out the line. Reassemble the valve, ensuring the large 'O' ring is properly seated.
How to fix ‘High Pres’ error on Tuttnauer 3140EA Laboratory Equipment?
If the 'High Pres' message appears on your Tuttnauer Laboratory Equipment, the air jet might be clogged; clean it. It could also mean that the heating elements are continuously on, or the temperature sensor is faulty. In these cases, contact a technician.
What should I do if my Tuttnauer 3140EA shows ‘Low Pres’?
If the 'Low Pres' message is displayed on your Tuttnauer Laboratory Equipment, clean the water level electrode inside the vessel. Also, ensure the door is fully closed, the door gasket is properly seated, and there is no steam leakage. Check the leveling of the machine.
How to troubleshoot Tuttnauer 3140EA machine not responding?
If your Tuttnauer Laboratory Equipment machine isn't responding, verify that the main switch is in the ‘On’ position, the power cord is properly connected to both the machine and the mains, and the circuit breaker hasn't tripped. Also, check the reset button on the cut-out thermostat.
How to clean a very dirty chamber in my Tuttnauer 3140EA?
If the chamber of your Tuttnauer Laboratory Equipment is very dirty, use Chamber Brite ™ to clean the autoclave; very dirty machines may require two cleanings.
What does ‘Low Heat’ mean on my Tuttnauer 3140EA Laboratory Equipment?
If the message ‘Low Heat’ is displayed during heat up on your Tuttnauer Laboratory Equipment, it indicates a bad temperature sensor. If heating elements are remaining on instead of cycling on and off, call for a technician.
What to do when my Tuttnauer 3140EA displays ‘High Temp’?
If your Tuttnauer Laboratory Equipment displays ‘High Temp’, clean the air jet and check for proper voltage at the wall outlet.
Inspect the autoclave's exterior and interior for damage upon arrival. Document any issues.
Table detailing electrical specifications, fuses, and circuit breakers for different models.
Comprehensive table of model specifications including chamber size, water volume, tray dimensions, and weight.
Detailed explanation of the program keys and other operational buttons on the control panel.
Explains common error messages, their causes, and corresponding safety measures.
Details nominal parameters and operational sequence for sterilizing unwrapped instruments.
Provides settings and sequence for sterilizing wrapped items and porous loads with drying.
Overview of daily, weekly, and periodic maintenance tasks to keep the autoclave in good working condition.
Instructions for cleaning the air jet located in the water reservoir to prevent spore test failures.
Step-by-step guide for using Chamber Brite cleaner to descale and clean the autoclave.
Troubleshooting steps for unresponsive machines and initial error displays like 'Low Heat', 'Low Water', 'Low Pres', 'Low Temp'.
Resolving 'High Temp', 'High Pres' errors, printer malfunctions, and continuous paper feed issues.
Addressing door leaks, long exhaust stages, and blocked water outlet strainers.
Troubleshooting clogged drains, failed spore tests, wet or burned items, and instrument rusting.
Resolving keyboard unresponsiveness, slow heat-up, noise, long drying times, and chamber filling problems.
General| Model | 3140EA |
|---|---|
| Type | Autoclave |
| Chamber Material | Stainless Steel |
| Power Supply | 50/60Hz |
| Operating Pressure | 2.1 Bar |
| Temperature Range | 105°C to 138°C |
To Next Page