What causes 'High Pres' to be displayed on Tuttnauer 3870E?
The 'High Pres' message on your Tuttnauer Laboratory Equipment can be due to a few reasons. It could mean the air jet is clogged and needs cleaning. Another possibility is that the heating elements are staying on instead of cycling. A faulty or dirty temperature sensor (PT100) could also be the cause. For the latter two issues, it's best to call a technician.
What to do if Tuttnauer 3870E Laboratory Equipment displays ‘Low Water’?
If the 'Low Water' message is displayed on your Tuttnauer Laboratory Equipment, clean the water level electrode inside the vessel. Also, ensure the door is fully closed with the gasket properly seated, and check that the machine is level. Replace the door gasket if there's any steam leakage.
How to clean a very dirty Tuttnauer 3870E Laboratory Equipment chamber?
To clean a very dirty chamber in your Tuttnauer Laboratory Equipment, use Chamber Brite ™. Very dirty machines may require two cleanings.
Why does Tuttnauer 3870E exhaust stage take so long?
If the exhaust stage of your Tuttnauer Laboratory Equipment cycle is taking a very long time, it's normal if you are running a ‘liquids’ program. The slow exhaust can take between 15 and 20 minutes.
Why are instruments rusting in my Tuttnauer 3870E Laboratory Equipment?
If instruments are rusting after sterilization in your Tuttnauer Laboratory Equipment, first determine if it's true rust by using a pencil eraser to remove the brown spot. If there is no pitting, the instrument is just dirty. Use distilled water for sterilizing and ensure dissimilar metals are not in contact with each other.
What to do if Tuttnauer 3870E Laboratory Equipment chamber is not filling?
If your Tuttnauer Laboratory Equipment chamber is not filling, check the water level in the reservoir and for any obstructions blocking the pickup tube. Clean the water sensor and try filling the machine manually using the Manual Inlet key.
What to do if Tuttnauer Laboratory Equipment printer prints blank paper?
If the printer of your Tuttnauer Laboratory Equipment prints, but nothing appears on the paper, ensure the paper is mounted correctly, as only one side is printable.
What to do if Tuttnauer 3870E process fails during heating stage with a HIGH TEMP message?
If your Tuttnauer Laboratory Equipment process fails while initiating the heating stage and displays a HIGH TEMP message, try changing the setting of the thermostat.
How to clean a very dirty chamber in my Tuttnauer 3870E Laboratory Equipment?
If the chamber of your Tuttnauer Laboratory Equipment is very dirty, use Chamber Brite ™ to clean the autoclave; very dirty machines may require two cleanings.
What does ‘Low Heat’ mean on my Tuttnauer 3870E?
If the message ‘Low Heat’ is displayed during heat up on your Tuttnauer Laboratory Equipment, it indicates a bad temperature sensor. If heating elements are remaining on instead of cycling on and off, call for a technician.
Details the manufacturer's warranty coverage for components and assembly.
Details the functions of program and other keys on the control panel.
Lists common messages and associated safety precautions.
Details the settings and sequence for sterilizing unwrapped instruments.
Settings and sequence for sterilizing wrapped instruments and porous loads.
Settings and sequence for sterilizing glassware with slow exhaust.
Guidelines for safe electrical connection and grounding.
Guidelines for safely loading and unloading items for sterilization.
Steps for initial setup, filling water, and selecting a sterilization program.
Instructions on starting the autoclave, monitoring stages, and changing parameters.
Overview of daily, weekly, and periodic maintenance tasks.
Instructions for cleaning the air jet to prevent sterilization failures.
Procedure for cleaning the autoclave using Chamber Brite.
Solutions for when the autoclave is unresponsive.
Troubleshooting steps for the 'Low Heat' error message.
Steps to resolve the 'Low Water' indicator.
Solutions for when the 'Low Pressure' message appears.
Troubleshooting for the 'High Temperature' error.
Steps to resolve the 'High Pressure' error message.
General| Type | Autoclave |
|---|---|
| Model | 3870E |
| Number of Trays | 3 |
| Weight | 240 lbs |
| Chamber Material | Stainless Steel |
| Sterilization Time Range | 4-60 Minutes |
| Sterilization Temperature Range | 121°C |
| Power Supply | 230V |
| Power Consumption | 1600 W |
| Dimensions (WxDxH) | 25 in x 29 in x 21 in |
To Next Page
