Why does my Tuttnauer Steriliser show 'Low Temp' and what should I do?
If your Tuttnauer Steriliser displays 'Low Temp', it means the temperature dropped below the sterilization temperature for more than 1 second during the sterilization cycle. To resolve this, perform a new cycle.
What to do if my Tuttnauer Steriliser displays 'Low Pressure'?
If the Tuttnauer Steriliser displays 'Low Pressure', it means the chamber pressure dropped below the sterilization pressure (134°C = 304 kPa, 121°C = 205 kPa) for 2 seconds during the sterilization stage. To solve this, perform a new cycle.
What does it mean if my Tuttnauer Steriliser shows 'High Pressure'?
If the Tuttnauer Steriliser displays 'High Pressure', it means the Chamber Pressure rose 4.2 psi-29 kPa above sterilization pressure (134°C = 304 kPa, 121°C = 205 kPa) for 2 seconds during the sterilization stage. Perform a new cycle.
What does 'Air Error' mean on my Tuttnauer Steriliser, and how can I fix it?
If the Tuttnauer Steriliser displays 'Air Error', it means the autoclave didn't reach atmospheric pressure 10 minutes after the drying stage started. Wait until the autoclave reaches atmospheric pressure and then perform a new cycle.
Why is my Tuttnauer Steriliser not responding?
If the Tuttnauer Steriliser is not responding, it could be due to several reasons: 1. The main switch might be in the ‘OFF’ position. Turn the main switch to the ‘On’ position. 2. The power cord might be disconnected. Ensure the power cord is properly connected to both the machine and the mains. 3. The circuit breaker might have tripped. Lift the circuit breaker lever.
What does 'Pressure Time Error' mean on my Tuttnauer Steriliser, and how can I troubleshoot it?
If the Tuttnauer Steriliser displays 'Pressure Time Error', it means the system couldn't reach the required pressure conditions in the chamber after the preset time during the air removal stage. Verify that the autoclave is not overloaded.
What does the error 'Heat Time Error (Keep)' indicate on my Tuttnauer Steriliser?
If the Tuttnauer Steriliser displays 'Heat Time Error (Keep)', it means the system couldn't reach the required temperature in the chamber during the optional "Keep Heat" stage within the preset time. Verify that the autoclave is not overloaded.
What does 'Low Pressure (Cooling)' mean on my Tuttnauer Steriliser, and how do I fix it?
If the Tuttnauer Steriliser displays 'Low Pressure (Cooling)', it means the pressure in the chamber didn't reach the preset pressure before the cooling stage. Check and fix the compressed air supply.
What does 'High Pressure (Ending)' mean on my Tuttnauer Steriliser, and how do I resolve it?
If the Tuttnauer Steriliser displays 'High Pressure (Ending)', it means the system cannot reach atmospheric pressure ± 5kPa during the ending stage. Perform a new cycle.
What does 'High Pressure (Exhaust)' indicate on my Tuttnauer Steriliser?
If the Tuttnauer Steriliser displays 'High Pressure (Exhaust)', it means the system cannot reach preset pressure within 10 minutes from the beginning of the exhaust stage. You should perform a new cycle.
Details the 5050 and 5075 vertical steam sterilizers.
Covers initial inspection of the unit and warranty terms.
Crucial safety precautions for autoclave operation, maintenance, and usage.
Introduces models and their purpose.
Specifies environmental, operational limits, and compliance standards.
Details technical specifications, dimensions, and electrical requirements.
Lists required utilities and maximum loading capacities for the unit.
Labels and identifies components shown in the front view diagram.
Labels and identifies components shown in the rear view diagram.
Provides visual representations and dimensions of the sterilizer models.
Illustrates the layout of the control panel.
Details the information displayed on the LCD screen during operation.
Explains the functions and usage of the control panel keys.
Lists and explains error messages and symbols for troubleshooting.
Describes operational messages and their required user actions.
Summarizes available sterilization programs and their settings.
Details parameters and sequence for unwrapped instrument sterilization.
Details parameters and sequence for wrapped instrument sterilization.
Details parameters and sequence for unwrapped pouch sterilization.
Details parameters and sequence for wrapped pouch sterilization.
Details parameters and sequence for unwrapped delicate instrument sterilization.
Details parameters and sequence for wrapped delicate instrument sterilization.
Allows user configuration of parameters for custom sterilization cycles.
Allows user configuration of parameters for custom sterilization cycles.
Specifies parameters for sterilizing liquids in unsealed bottles.
Specifies parameters for sterilizing liquids in sealed bottles.
Outlines the system's menu structure for accessing settings and data.
Provides a table of default parameters for custom programs.
Guides users on how to navigate to the main system menu.
Details how to configure parameters for Custom 1 and Custom 2 programs.
Explains how to adjust system-wide settings.
Covers viewing and exporting historical cycle data.
Details scheduled tasks for maintaining the autoclave's condition.
Covers daily, weekly, and periodic cleaning and checks.
Procedure for testing the safety valve's functionality.
Provides solutions for common malfunctions and error messages.
Lists available spare parts with their catalog numbers.
Lists optional accessories with their catalog numbers.
General| Type | Autoclave |
|---|---|
| Chamber Volume | 75 liters |
| Power Supply | 230V, 50/60Hz |
| Sterilization Temperature Range | 121°C to 134°C |
| Number of Trays | 3 |
| Chamber Material | Stainless Steel |
| Weight | 120 kg |
| Power | 3.0 kW |
| Power Consumption | 3, 000 watts |
| Temperature Range | 105°C to 137°C |
| Sterilization Time Range | 5 to 60 minutes |
| Exterior Material | Steel |
| Safety Features | Over-temperature protection, pressure relief valve |
| Cycle Time | Varies depending on load size and sterilization parameters |
To Next Page
