What causes the safety relief valve on my Tuttnauer Laboratory Equipment to open at a lower pressure than specified?
If the safety relief valve on your Tuttnauer Laboratory Equipment opens at a pressure lower than specified, it could be clogged or faulty. Replace the relief valve and check the water quality to resolve this.
Why does the safety relief valve on my Tuttnauer 5075 Laboratory Equipment open at a pressure higher than specified?
If the safety relief valve on your Tuttnauer Laboratory Equipment opens at a pressure higher (more than 10%) than specified, the relief valve is likely faulty and needs replacement.
Why doesn't the safety relief valve on my Tuttnauer Laboratory Equipment close in time?
If the safety relief valve on your Tuttnauer Laboratory Equipment does not close in time (2-3 seconds), the valve is likely faulty and needs replacement.
What does 'High Temp' mean on my Tuttnauer Steriliser, and how do I resolve it?
If the Tuttnauer Steriliser displays 'High Temp', it means the temperature rose 7°F (4°C) above the sterilization temperature during the sterilization stage for 2 seconds. You should perform a new cycle.
Why is the safety relief valve on my Tuttnauer 5075 Laboratory Equipment constantly leaking?
If the safety relief valve on your Tuttnauer Laboratory Equipment leaks constantly, the valve is likely faulty and needs replacement. Additionally, check the water quality.
What to do if 'Low Vacuum' is displayed on my Tuttnauer Steriliser?
If the Tuttnauer Steriliser displays 'Low Vacuum,' it means that the vacuum level of 15kPa was not reached within 20 minutes after the cycle started. You can try performing a new cycle. If the issue continues, it may require technical assistance. Also, the bio-hazard filter may be clogged and require technical service.
What does 'High Temp. (Ending)' mean on my Tuttnauer Steriliser and how can I fix it?
If the Tuttnauer Steriliser displays 'High Temp. (Ending)', it means the system cannot reach the required temperature in the chamber within 10 minutes since exhaust. You should perform a new cycle.
What does 'Heat Time Error' mean on my Tuttnauer Steriliser, and how do I fix it?
If the Tuttnauer Steriliser displays 'Heat Time Error', it means the system couldn't reach the required temperature in the chamber within the preset time. Make sure that the autoclave is not overloaded.
What causes a 'No Water' error on my Tuttnauer Steriliser and how can I resolve it?
If the Tuttnauer Steriliser displays 'No Water', it means the electrode in the chamber didn't sense water within the preset time. First, check and fix the mineral-free water supply. Then, check and clean the water inlet filter. Finally, clean the water level electrode.
How to fix 'High Temp. (Cooling)' error on Tuttnauer Steriliser?
If the Tuttnauer Steriliser displays 'High Temp. (Cooling)', this indicates that the system cannot reach the sterilization temperature during the cooling stage within the preset time. Check and fix the city (tap) water supply.
Details the 5050 and 5075 vertical steam sterilizers.
Covers initial inspection of the unit and warranty terms.
Crucial safety precautions for autoclave operation, maintenance, and usage.
Introduces models and their purpose.
Specifies environmental, operational limits, and compliance standards.
Details technical specifications, dimensions, and electrical requirements.
Lists required utilities and maximum loading capacities for the unit.
Labels and identifies components shown in the front view diagram.
Labels and identifies components shown in the rear view diagram.
Provides visual representations and dimensions of the sterilizer models.
Illustrates the layout of the control panel.
Details the information displayed on the LCD screen during operation.
Explains the functions and usage of the control panel keys.
Lists and explains error messages and symbols for troubleshooting.
Describes operational messages and their required user actions.
Summarizes available sterilization programs and their settings.
Details parameters and sequence for unwrapped instrument sterilization.
Details parameters and sequence for wrapped instrument sterilization.
Details parameters and sequence for unwrapped pouch sterilization.
Details parameters and sequence for wrapped pouch sterilization.
Details parameters and sequence for unwrapped delicate instrument sterilization.
Details parameters and sequence for wrapped delicate instrument sterilization.
Allows user configuration of parameters for custom sterilization cycles.
Allows user configuration of parameters for custom sterilization cycles.
Specifies parameters for sterilizing liquids in unsealed bottles.
Specifies parameters for sterilizing liquids in sealed bottles.
Outlines the system's menu structure for accessing settings and data.
Provides a table of default parameters for custom programs.
Guides users on how to navigate to the main system menu.
Details how to configure parameters for Custom 1 and Custom 2 programs.
Explains how to adjust system-wide settings.
Covers viewing and exporting historical cycle data.
Details scheduled tasks for maintaining the autoclave's condition.
Covers daily, weekly, and periodic cleaning and checks.
Procedure for testing the safety valve's functionality.
Provides solutions for common malfunctions and error messages.
Lists available spare parts with their catalog numbers.
Lists optional accessories with their catalog numbers.
General| Type | Autoclave |
|---|---|
| Chamber Volume | 75 liters |
| Power Supply | 230V, 50/60Hz |
| Sterilization Temperature Range | 121°C to 134°C |
| Number of Trays | 3 |
| Chamber Material | Stainless Steel |
| Weight | 120 kg |
| Power | 3.0 kW |
| Power Consumption | 3, 000 watts |
| Temperature Range | 105°C to 137°C |
| Sterilization Time Range | 5 to 60 minutes |
| Exterior Material | Steel |
| Safety Features | Over-temperature protection, pressure relief valve |
| Cycle Time | Varies depending on load size and sterilization parameters |
To Next Page
