What does 'Door Error (following opening the door)' mean on my Tuttnauer 5075 Laboratory Equipment and how do I fix it?
If your Tuttnauer Laboratory Equipment displays a 'Door Error (following opening the door)', it could be due to disconnected or faulty micro-switches actuated by the motor mechanism. Fix any disconnections, and if the problem persists, replace the faulty micro-switches.
What does 'Error Locking (following closing the door)' mean on my Tuttnauer 5075 Laboratory Equipment and how do I resolve it?
If your Tuttnauer Laboratory Equipment displays an 'Error Locking (following closing the door)', it could be due to disconnected or faulty micro-switches on the door frame. Fix any disconnections, and if the problem persists, replace the faulty micro-switches.
What does 'I/O Card Failure' mean on my Tuttnauer Laboratory Equipment and how can I fix it?
If your Tuttnauer Laboratory Equipment shows an 'I/O Card Failure', it could be due to a disconnection between the I/O board and the Main board, or the I/O card itself is faulty. Fix any disconnections, and if the problem persists, replace the faulty I/O card.
What to do if my Tuttnauer Steriliser displays 'Low Pressure'?
If the Tuttnauer Steriliser displays 'Low Pressure', it means the chamber pressure dropped below the sterilization pressure (134°C = 304 kPa, 121°C = 205 kPa) for 2 seconds during the sterilization stage. To solve this, perform a new cycle.
What does it mean if the chamber temperature is not in range on my Tuttnauer Laboratory Equipment?
If your Tuttnauer Laboratory Equipment displays that the chamber temperature is not in range, it could be due to several reasons: the 'End Temperature' parameter has been changed and is too low, a faulty temperature sensor, or a faulty command to the heating elements due to a short-circuit or a faulty I/O board. Correct the parameter. If the issue persists, replace the faulty sensor. Also, fix any short-circuits or replace the I/O board.
What to do if Tuttnauer 5075 displays ‘High Temp’?
If the Tuttnauer Laboratory Equipment displays ‘High Temp’, clean the water level electrode inside the vessel and check the leveling of the machine.
Why is my Tuttnauer Steriliser leaking at the door?
If the Tuttnauer Steriliser is leaking at the door, it could be due to a dirty or damaged door gasket. Clean the door gasket. Also, clean the surface against the door. If the issue persists, call for service.
How to fix Tuttnauer Laboratory Equipment when the printer prints but nothing is on the paper?
If the printer prints, but nothing appears on the paper, ensure the paper is mounted correctly, as only one side is printable. Also, make sure the paper is inserted in the printer. If the issue persists, switch off the machine and switch it back on while pressing the feed button on the printer. If a test printout appears, the printer is working, and there may be an electronics issue.
What does 'Supply distilled water error (digital input option)' mean on my Tuttnauer 5075 Laboratory Equipment and how do I fix it?
If your Tuttnauer Laboratory Equipment displays a 'Supply distilled water error (digital input option)' message, it indicates a malfunction in the mineral-free water supply. To resolve this, check and fix the mineral-free water supply.
What does 'Power Down' mean on my Tuttnauer 5075 Laboratory Equipment and how do I recover?
If your Tuttnauer Laboratory Equipment displays a 'Power Down' message, it means a power outage occurred during the cycle. Turn on the autoclave, wait until it is ready (reaches a safe condition), and then perform a new cycle.
Details the 5050 and 5075 vertical steam sterilizers.
Covers initial inspection of the unit and warranty terms.
Crucial safety precautions for autoclave operation, maintenance, and usage.
Introduces models and their purpose.
Specifies environmental, operational limits, and compliance standards.
Details technical specifications, dimensions, and electrical requirements.
Lists required utilities and maximum loading capacities for the unit.
Labels and identifies components shown in the front view diagram.
Labels and identifies components shown in the rear view diagram.
Provides visual representations and dimensions of the sterilizer models.
Illustrates the layout of the control panel.
Details the information displayed on the LCD screen during operation.
Explains the functions and usage of the control panel keys.
Lists and explains error messages and symbols for troubleshooting.
Describes operational messages and their required user actions.
Summarizes available sterilization programs and their settings.
Details parameters and sequence for unwrapped instrument sterilization.
Details parameters and sequence for wrapped instrument sterilization.
Details parameters and sequence for unwrapped pouch sterilization.
Details parameters and sequence for wrapped pouch sterilization.
Details parameters and sequence for unwrapped delicate instrument sterilization.
Details parameters and sequence for wrapped delicate instrument sterilization.
Allows user configuration of parameters for custom sterilization cycles.
Allows user configuration of parameters for custom sterilization cycles.
Specifies parameters for sterilizing liquids in unsealed bottles.
Specifies parameters for sterilizing liquids in sealed bottles.
Outlines the system's menu structure for accessing settings and data.
Provides a table of default parameters for custom programs.
Guides users on how to navigate to the main system menu.
Details how to configure parameters for Custom 1 and Custom 2 programs.
Explains how to adjust system-wide settings.
Covers viewing and exporting historical cycle data.
Details scheduled tasks for maintaining the autoclave's condition.
Covers daily, weekly, and periodic cleaning and checks.
Procedure for testing the safety valve's functionality.
Provides solutions for common malfunctions and error messages.
Lists available spare parts with their catalog numbers.
Lists optional accessories with their catalog numbers.
General| Type | Autoclave |
|---|---|
| Chamber Volume | 75 liters |
| Power Supply | 230V, 50/60Hz |
| Sterilization Temperature Range | 121°C to 134°C |
| Number of Trays | 3 |
| Chamber Material | Stainless Steel |
| Weight | 120 kg |
| Power | 3.0 kW |
| Power Consumption | 3, 000 watts |
| Temperature Range | 105°C to 137°C |
| Sterilization Time Range | 5 to 60 minutes |
| Exterior Material | Steel |
| Safety Features | Over-temperature protection, pressure relief valve |
| Cycle Time | Varies depending on load size and sterilization parameters |
To Next Page
