UTECH VS2000V User Manual (English)

Questions and Answers:

C
Crystal ShawAug 8, 2025
Why is the pulse rate erratic on my UTECH Monitor?
- G
  Gregory TurnerAug 8, 2025
  If the pulse rate on your UTECH Monitor is erratic, intermittent, or incorrect, it might be due to several reasons. First, ensure the SpO2 sensor is correctly positioned on the patient. The patient's movement or poor perfusion can also cause this issue, so ensure the patient remains still. Also, too much ambient light around the SpO2 sensor can interfere with readings; try shielding the sensor with a towel.
D
Donald WangAug 12, 2025
How to fix a UTECH VS2000V when the power LED is not lit?
- E
  Eric WilliamsAug 12, 2025
  If the AC power LED on the front of your UTECH Monitor isn't lit, it could be due to a few reasons. Check that the AC power cord is properly connected to both the monitor and the AC line. Ensure the power cord is connected to an outlet not controlled by a wall switch. If these steps don't resolve the issue, it's possible the AC line fuse has blown, and you should contact your authorized repair center.
L
Laura DanielsAug 16, 2025
What to do if my UTECH VS2000V Monitor displays 'SENSOR OFF'?
- M
  Mary CobbAug 16, 2025
  If the UTECH Monitor displays 'SENSOR OFF' in the Pleth waveform channel, it could be due to a few reasons. First, check the SpO2 sensor's position on the patient and reposition if necessary. If the issue persists, verify that you're using the correct SpO2 sensor for the application. The sensor itself might be defective, in which case you should change the sensor or contact the manufacturer service department.
D
david69Aug 20, 2025
Why is there no peripheral pulse registering on my UTECH VS2000V Monitor?
- V
  Vanessa FergusonAug 21, 2025
  If the bargraph in the SpO2 parameter box on your UTECH Monitor shows no peripheral pulse, start by checking the SpO2 sensor connection. Ensure it's correctly connected to the extension cable, and the extension cable is connected to the monitor. Also, verify the sensor's position on the patient and reposition it if needed. If the issue continues, the SpO2 sensor or the extension cable might be defective. In this case, change the sensor or contact the manufacturer service department.
B
Benjamin ThomasAug 25, 2025
What does 'LEADS FAIL' mean on my UTECH VS2000V?
- S
  Sherri KrauseAug 25, 2025
  If your UTECH Monitor displays 'LEADS FAIL' in the ECG waveform channel, it indicates a problem with the ECG leads. Ensure that each ECG lead is properly connected to the electrode. If the leads are connected but the error persists, one of the ECG leads may be broken, and you should replace them. Alternatively, the electrode's impedance might be too high, requiring you to reapply the electrodes.
Y
Yvonne PattersonAug 29, 2025
Why does the display on my UTECH VS2000V Monitor not light up?
- R
  Rachel MarquezAug 29, 2025
  If the display on your UTECH Monitor does not light up, it could indicate that the display backlight is defective. In this case, contact the service department.
A
Adrian HicksSep 2, 2025
Why is the battery life so short on my UTECH VS2000V?
- J
  Joshua WardSep 2, 2025
  If the battery run time is excessively short on a fully charged battery of your UTECH Monitor, it means the battery is spent. Contact your authorized repair center.

UTECH VS2000V Specifications

General

Brand	UTECH
Model	VS2000V
Category	Monitor
Language	English

Related product manuals

UTECH VS2000

122 pages

UTECH VS2000V User Manual

Table of Contents

Questions and Answers:

UTECH VS2000V Specifications

Related product manuals