Vega PEL-4 - User Manual

PEL-4 LED Precision Sector Light
All Horizontal Divergence Models
Installation, Operation and Programming Manual
IMPORTANT: If oscillating boundary has been installed, remove temporary packers
from inside of PEL-4 before first use.
CAUTION: The PEL-4 is a source of bright light. Do not stare directly into the beam
from close range. Observe all warnings and guidelines in this instruction manual.
PEL-4 Product Manual
Available colour range Red, Green or White
Available models 3.5D, 5D, 10D
Sector number & sub tenses Custom
Software version: 2.2.9+
Product version: 3.00
Manual version: 1.06
Date released: August 2018
V E G A I N D U S T R I E S L I M I T E D

Vega PEL-4 Specifications

General

Brand	Vega
Model	PEL-4
Category	Industrial Equipment
Language	English

Summary

Introduction to the PEL-4 Precision LED Sector Light

Overview

General description of the PEL-4, its features, and capabilities.

Quick-start Guide

Provides simple steps for initial PEL-4 setup and operation.

Automatic Flash Compensation

Explains how effective intensity is compensated based on flash character.

PEL-4 Intensity Specification

Details the intensity specifications and programming for PEL-4 models.

Electrical Connection

Power Connection

Information on connecting the PEL-4 to a power supply.

Hardwire Sync Connection

Details on using hardwire sync for synchronizing multiple beacons.

DataPort

Explains the interface connections provided by the DataPort option.

Mounting and Alignment

Mounting

Describes the mounting plates and hole specifications for PEL-4 models.

Alignment

Explains the horizontal and vertical adjustment screws for PEL-4 alignment.

Programming

Programming Syntax

Details the syntax for programming parameters using the TVIR programmer.

Visual Feedback when Using the TVIR Programmer

Explains how the PEL-4 provides feedback during programming.

If the PEL-4 will not enter Programming Mode

Troubleshooting steps for issues entering programming mode.

Becoming Familiar with the Programming Syntax and Flash Feedback

Guidance on practicing programming and understanding feedback.

Deciding which Settings are required

Advice on determining necessary settings and using read features.

Programming or Reading Multiple Settings

Information on programming or reading multiple parameters in one sequence.

Normal, Automatic Operating Mode

Flash Character

Describes pre-programmed and custom flash characters available for the PEL-4.

Custom Flash Character

Instructions for programming custom flash characters with specific on/off periods.

Day;Night Automatic Operation of the PEL-4

How the PEL-4 uses a photocell for automatic day/night switching.

Night & Day Intensity Settings

How to program separate intensity levels for night and day operation.

Synchronising Options

Details on hardwired and GPS synchronization methods.

Battery Thresholds

Programmable settings to protect the battery from over-discharge.

Performing System Checks

Setting a Security PIN Number

Flash Character Modes

Flash Compensation Modes

Explains IALA E-200-4 2017, 2008, and disabled flash compensation modes.

Remote Control Operation

Enabling Remote Control Operation

Steps to enable and configure remote control features via programming.

Remote Control Inputs

Details on hardwired inputs for remote control.

Serial Remote Control Interface

Information on using serial commands for remote control.

Serial Remote Control Mode Changes

Modifying remote control modes via serial interface.

Simultaneous Use of Remote Control Hardwired Inputs and Serial Interface

How hardwired and serial controls work together.

Routine Maintenance

Maintenance Cleaning

Instructions for cleaning the exterior and internal components of the PEL-4.

Inspection check

Periodic checks for mounting security, fastener condition, and corrosion.

APPENDIX A PROGRAMMING TABLE

Appendix A.1 Generic TVIR Programming Commands

Lists generic programming commands for the TVIR programmer.

APPENDIX B INTENSITY SETTINGS AND CURRENTS

Appendix B.1 3.5 D Models

Intensity and current data for PEL-4 3.5D models.

Appendix B.2 5 D Models

Intensity and current data for PEL-4 5D models.

Appendix B.3 10 D Models

Intensity and current data for PEL-4 10D models.

APPENDIX C PEL-4 DIMENSIONS BY MODEL

APPENDIX D SPECIFICATIONS OF PEL-4

APPENDIX E FLASH CHARACTER TABLE WITH PROGRAMMING CODES

APPENDIX F SERIAL INTERFACE COMMANDS