Videx 4000 Series - Page 43

66250754-EN - V1.0 - 18/02/19
- 43 -
4000 Series GSM Audio Intercom - Technical Manual
4000 Series GSM Audio Intercom with Proximity
Programming the GSM Intercom
1111SPTnn? Store the time nn x 20 seconds (e.g. nn = 02, time = 40 seconds, refer to table below), also
send a conrmation text back to the sender.
1111SPT? Query the current stored time. A text message will be sent back to the sender showing the
stored time (remember to multiply the number in the received text by 20 seconds).
nn multiplier: nn = 01, time = 20 secs nn = 02, time = 40 secs nn = 03, time = 60 secs
nn = 04, time = 80 secs nn = 05, time = 100 secs nn = 06, time = 120 secs
nn = 07, time = 140 secs nn = 08, time = 160 secs nn = 09, time = 180 secs
nn = 10, time = 200 secs nn = 11, time = 220 secs nn = 12, time = 240 secs
SET RELAY TIME RLT
The relay time can be from 01 – 99 seconds or latching (set the relay time to 00 for latched mode. In latch mode, the relay will stay
energised until the command is sent again).
1111RLTnn Store the relay time nn = time in seconds (e.g. nn = 05, time = 5 seconds).
1111RLTnn? Store the relay time nn = time in seconds. Also send a conrmation text back to the sender.
1111RLT? Query the current stored relay time. A text message will be sent back to the sender
showing the stored relay time.
SET AUXILIARY OUTPUT AO1 TIME A1T, FOR A1M = 01 ONLY
The auxiliary output AO1 time can be set from 01 - 99 seconds or latching (set the AO1 output time to 00 for latched mode. In latch
mode the AO1 output will stay triggered until the relevant command is sent again to unlatch the AO1 output. This option is only
available when the AO1 output mode, A1M, is set to mode 01. Please refer to the A1M commands below for more details).
1111A1Tnn Store the AO1 time nn = time in seconds (e.g. nn = 05, time = 5 seconds).
1111A1Tnn? Store the AO1 time nn = time in seconds. Also send a conrmation text back to the sender.
1111A1T? Query the current stored AO1 time. A text message will be sent back to the sender showing
the stored AO1 time.
SET AUXILIARY OUTPUT AO1 MODE A1M, MODES 00  05
The auxiliary output AO1 has up to six modes that can be set:
Call Activated: nn = 00
AO1 output will activate when a call begins and deactivate when a call ends. See example, Fig.30, on page 22.
User Activated: nn = 01
To activate the AO1 output either short terminals g to 5 (auxiliary 1 input) on the GSM PRO intercom or press 6 on the telephone
during a call. See example, Fig.31, on page 22.
Used for Status Indication: nn = 02
When in this mode, the AO1 terminal is used exclusively for monitoring the status of an input. For example, checking if a gate/door
is open or closed. See example, Fig.32, on page 23.
Divert Calls to Master Number: nn = 03
When in this mode, the AO1 terminal is used exclusively for monitoring the status of a switched input to decide if calls should be
diverted to the master number or not. See example, Fig.33, on page 23.
Call Activate (Timed): nn = 04
AO1 output will activate when a call begins and deactivate when the auxiliary 1 output time (A1T) expires. See example, Fig.34, on
page 24.
Enable/Disable “Dial to Open”: nn = 05
When in this mode, the AO1 terminal is used to enable/disable the dial to open feature via an external C/NO switched input across
terminals AO1 & g, (for example the C/NO relay contacts on a timeclock could be connected across terminals AO1 & g on the GSM
PRO intercom. When the timeclock relay is ON then no dial to open numbers are allowed. The GSM PRO answers the call and awaits
the master code to be entered. When the timeclock relay is OFF all dial to open numbers will operate as normal). See example,
Fig.35, on page 24.
1111A1Mnn Store the AO1 mode nn = 00 - 05.
1111A1Mnn? Store the AO1 mode nn = 00 - 05. Also send a conrmation text back to the sender.
1111A1M? Query the current stored AO1 mode. A text message will be sent back to the sender
showing the stored A1O mode.