Videx 4000 Series - Programming the GSM Intercom

66250754-EN - V1.0 - 18/02/19
- 37 -
4000 Series GSM Audio Intercom - Technical Manual
4000 Series GSM Audio Intercom with Proximity
Programming the GSM Intercom
PROGRAMMING THE GSM INTERCOM
Programming the GSM PRO intercom can be carried out in two ways, either by sending text (SMS) messages or by using the GSMSK
PC software (ver 4.0.0.0 or later), also refer to the programming manual GSMSK_66251720_EN_V2-0 (or later).
IMPORTANT NOTE: When you are required to use “ in a text message it is very important to use the correct symbol and not for
example ‘ (or two ‘ single apostrophes side by side which you will see look the same but will be interpreted dierently by the
GSM PRO intercom panel).
PROGRAMMING BY TEXT MESSAGE
Programming by text message is a simple way to customise the settings of the GSM PRO intercom panel and add or delete telephone
numbers. If you have a large number of buttons or telephone numbers to enter you may nd programming easier with the GSMSK
PC software. Simply send texts in the following format shown below to the telephone number of the SIM within the GSM PRO
intercom panel:
<4 DIGIT CODE> <3 DIGIT FUNCTION CODE> <OPTIONAL DATA> <OPTIONAL ?>
4 DIGIT CODE
This code prevents unauthorised access to the programmable features of the system. The code must
be four digits long but can be any combination using digits 0 – 9. The default code is 1111 and will
be used for all examples in this manual.
3 DIGIT FUNCTION CODE
The 3 digit function code identies the programmable feature to be changed. The code must be in
capital letters. The following table lists the available codes.
DESCRIPTION CODE EXAMPLE SETTINGS DEFAULT PAGE
Store a primary telephone no. STN 1111STNnnn”01912243174” nnn = 001 - 050 n/a 39 - 40
Store divert 1 telephone no. STD 1111STDnnn”01912241559” nnn = 001 - 050 n/a 39 - 40
Store divert 2 telephone no. STE 1111STEnnn”01912243678” nnn = 001 - 050 n/a 39 - 40
Store divert 3 telephone no. STF 1111STFnnn”01912245326” nnn = 001 - 050 n/a 39 - 40
Store a primary telephone no.
and divert no’s in a single text
message
STN 1111STNnnn”pn”,”d1”,”d2”,”d3”
1111STNnnn”01912243174”,
”01912241559”,” 01912243678”,
”01912245326”
nnn = 001 - 050
pn = primary no.
d1 = divert 1 no.
d2 = divert 2 no.
d3 = divert 3 no.
n/a 40
Store a dial to open no. (DTO)
or
Store up to 5 dial to open no’s
(DTO) in a single text message to
the next available locations
STR 1111STRnnn”07771234567”
1111STR”n1”,”n2”,”n3”,”n4”,”n5”
1111STR”01912243174”,
”01912241559”,” 01912243678”,
”01912245326”,”07897123456”
nnn = 000 - 999 or
nnn = optional
n1 = 1st DTO
n2 = 2nd DTO
n3 = 3rd DTO
n4 = 4th DTO
n5 = 5th DTO
n/a 41 - 42
Delete a dial to open no. without
knowing it’s location
DET 1111DET”01912243174” n/a n/a 42
Set call time SPT 1111SPTnn nn = 01 - 12 02 (40s) 42 - 43
Set relay time RLT 1111RLTnn nn = 00 - 99 05 (5s) 43
Set auxiliary AO1 output time A1T 1111A1Tnn nn = 00 - 99 05 (5s) 43
Set auxiliary AO1 out mode A1M 1111A1Mnn nn = 00 - 05 01 43
Set auxiliary AO2 output time A2T 1111A2Tnn nn = 00 - 99 05 (5s) 44
Keep connection facility NOD 1111NODnn nn = 01 - 99 0 (disabled) 44
Divert to next no. time DIT 1111DITnn nn = 01 - 99 15 (15s) 44
Check GSM signal strength SIG 1111SIG? n/a n/a 44
Check software version VER 1111VER? n/a n/a 44
Dial a number DLE 1111DLE”123” n/a n/a 44 - 45
Store SMS message for g-4 SMS 1111SMS”HouseAlarm” n/a AUX TRIG 45
Change 4 digit code CDE 1111CDE1234 Any 4 digits 1111 45
Trigger the relay RLY 1111RLY n/a n/a 45
Trigger the auxiliary output AO1 A1O 1111A1O n/a n/a 45
Trigger the auxiliary output AO2 A2O 1111A2O n/a n/a 45
Store balance check dial string SDL 1111SDL”*#1345#” n/a n/a 45
Check credit balance BAL 1111BAL? n/a n/a 45 - 46