Videx 4000 Series - User Commands

66250754-EN - V1.0 - 18/02/19
- 66 -
4000 Series GSM Audio Intercom - Technical Manual
4000 Series GSM Audio Intercom with Proximity
USER COMMAND TABLES
The following user command table shows the user commands that can be carried out during a call. Successful commands are
signalled by two beeps from the telephone, errors are signalled by four beeps.
IMPORTANT NOTE: When the ED# function has been enabled the user must press the # button on their phone before pressing
any of the following user commands (also refer to page 52 for further information).
FUNCTION 1st KEY TO PRESS 2nd KEY TO PRESS
Latch the relay (unlatch by pressing 3) 1 0
Release the door or gate 3 n/a
Activate auxiliary output AO1
1
(when A1M = mode 01) 6 n/a
Activate auxiliary output AO2
2
5 n/a
Adjust door speech volume (GSM speaker) 4 0 - 9 (0 = lowest, 9 = highest)
Adjust phone speech volume (GSM mic) 7 0 - 9 (0 = lowest, 9 = highest)
Status Indication for AO1
3
(when A1M = mode 02) 9 n/a
  Activating auxiliary output AO1 in this way is only possible when A1M mode has been set to mode 01 (also see notes on page
43, ‘set auxiliary output AO1 mode’) and will operate for the programmed AO1 time. If the AO1 output time has been set to latch
simply press 6 on the phone to unlatch the output again.
  Auxiliary output AO2 will activate for the programmed AO2 time. If the AO2 output time has been set to latch simply press 5 on
the phone to unlatch the output again.
  Auxiliary input AO1 status indication is only possible when A1M mode has been set to mode 02 (also see notes on page 43, ‘set
auxiliary output AO1 mode’).
The next user command table shows the SMS text messages that can be sent to the GSM intercom while in standby (the examples
shown in the table use the default 4 digit master code 1111).
FUNCTION MESSAGE TO SEND
Check the signal strength 1111SIG?
Check the available balance
4
1111BAL?
Check the software version 1111VER?
Release the door/gate 1111RLY? (? optional, send if conrmation is required)
Latch the relay 1111RLA? (? optional, send if conrmation is required)
Unlatch the relay 1111RUL? (? optional, send if conrmation is required)
Activate auxiliary output AO1 1111A1O? (? optional, send if conrmation is required)
Latch auxiliary output AO1 1111A1L? (? optional, send if conrmation is required)
Unlatch auxiliary output AO1 1111A1U? (? optional, send if conrmation is required)
Activate auxiliary output AO2 1111A2O? (? optional, send if conrmation is required)
Latch auxiliary output AO2 1111A2L? (? optional, send if conrmation is required)
Unlatch auxiliary output AO2 1111A2U? (? optional, send if conrmation is required)
Check Timeband setting (for call buttons) 1111TBA?
Query Access Control Timeband (0 - 9) 1111ATBn? (where n = timeband no. 0 - 9, also see notes on pages 48 - 49)
Query Access Level (0 - 9) 1111ACCn? (where n = access level no. 0 - 9, also see notes on page 50)
Check Intercom Time and Date 1111CLK?
Check Input Status 1111CHK?
Find a Dial to Open (DTO) number (000 -
999)
1111FDT”yyyyyyyyyyy”? (where yyyyyyyyyyy = telephone number, minimum of 4
digits, also see notes on pages 58 - 59)
Find a Fob or Card location (000 - 999) 1111FDF”nnnnn”? (where nnnnn = 5 digit user code printed on fob/card, also see
notes on page 54)
Find an Access Code (000 - 399) 1111FDC”code”? (where code = 4 to 8 digit access code, also see notes on page 57)
  The balance can only be checked if the correct balance check string has been stored (also see SDL notes on page 45 - 46). This
feature is only applicable for pay-as-you-go SIM cards.
User Commands