To Next PageTo Next PageWhy is my USB drive failing on ViewSonic PLED-W500 Projector?
If your ViewSonic Projector has USB drive failure, the USB might not support the USB hub function or its power consumption might be over 500mA.
How to adjust ViewSonic PLED-W500 image size?
If the image from your ViewSonic Projector is too small or too large, move the projector closer to or further from the screen to adjust the size. Alternatively, press 'Menu' on the remote or control panel, navigate to 'SCREEN' --> 'Aspect Ratio,' and experiment with different settings.
What to do if ViewSonic PLED-W500 image is out of focus?
If the image is out of focus, first, ensure that the lens cap is removed. Then, adjust the 'Focus Ring' on the projector lens. Also, make sure the projection screen is within the required distance of 1.71-9.84 feet (0.52-3.00 meters) from the projector.
What to do if ViewSonic Projector image is too small or too large?
If the image is too small or too large, move the projector closer to or further from the screen. Alternatively, press 'Menu' on the remote control or on the control panel, go to 'SCREEN' --> 'Aspect Ratio', and try the different settings.
Why is my ViewSonic Projector image out of focus?
If the image from your ViewSonic Projector is out of focus, first ensure that the lens cap is removed. Then, adjust the 'Focus Ring' on the projector lens. Also, make sure the projection screen is within the required distance of 1.71-9.84 feet (0.52-3.00 meters) from the projector.
Why ViewSonic PLED-W500 USB/SD read fail?
If your ViewSonic Projector fails to read from a USB device or SD card, ensure that the USB device or SD card is in good condition and properly inserted. If necessary, remove and re-insert it several times.
How to fix partial image on ViewSonic PLED-W500?
If you are experiencing a partial, scrolling, or incorrectly displayed image on your ViewSonic Projector, press 'Auto' on the remote control or on the control panel. If you are using a PC, open the 'My Computer' icon, then the 'Control Panel' folder, and double-click the 'Display' icon. Select the 'Settings' tab and ensure your display resolution setting is lower than or equal to 1080p. Click on 'Advanced Properties'. If you are using a Notebook, follow the steps above to adjust the computer's resolution and press the toggle output settings (e.g., [Fn]+[F4]).
Why is my ViewSonic Projector image stretched?
If the image from your ViewSonic Projector is stretched when displaying a 16:9 DVD title, change the format to 4:3 in the projector's OSD if you are playing a 4:3 format DVD. If the image is still stretched, set up the display format as 16:9 (wide) aspect ratio type on your DVD player.
How to correct a reversed image on a ViewSonic Projector?
If the image is reversed, and the projector is mounted on the ceiling, select 'SCREEN' --> 'Auto Ceil Mount' from the OSD and adjust the projection direction. If the projector is placed on the desk, select 'SETTING' --> 'Orientation' from the OSD and adjust the projection direction.
ViewSonic PLED-W500 not responding, how to fix?
If your ViewSonic Projector stops responding to all controls, turn off the projector, unplug the power cord, and wait at least 20 seconds before reconnecting the power.
General| Matrix size | 0.45 \ |
|---|---|
| Number of colors | 16.78 million colors |
| Projection distance | 0.91 - 2.4 m |
| Vertical scan range | 48 - 120 Hz |
| Horizontal scan range | 31 - 100 kHz |
| Projection technology | DLP |
| Contrast ratio (typical) | 6000:1 |
| Screen size compatibility | 30 - 80 \ |
| Projector native resolution | WXGA (1280x800) |
| Keystone correction, vertical | -40 - 40 ° |
| Aspect ratio | 16:10 |
| RS-232 ports | - |
| Network ready | No |
| Dimensions (WxDxH) | 214 x 164 x 42 mm |
| Connectivity technology | Wired |
| Maximum analog resolution | 1680 x 1050 pixels |
| Maximum digital resolution | 1920 x 1080 pixels |
| Focus | Manual |
| Focal length range | - mm |
| Lamps quantity | 1 lamp(s) |
| Light source type | LED |
| Service life of light source | 20000 h |
| PC Audio in | Yes |
| USB connector type | USB Type-A |
| USB 2.0 ports quantity | 2 |
| S-Video inputs quantity | 1 |
| Ethernet LAN (RJ-45) ports | 0 |
| Supported video modes | 1080i, 1080p, 480i, 480p, 576i, 576p, 720p |
| Analog signal format system | NTSC, PAL, SECAM |
| Supported graphics resolutions | 1440 x 1050, 1680 x 1050 (WSXGA+), 640 x 480 (VGA) |
| RMS rated power | 2 W |
| Audio formats supported | MP3 |
| Video formats supported | H.264, MPEG2, MPEG4 |
| Product color | Black |
| Market positioning | Portable |
| AC input voltage | 100 - 240 V |
| AC input frequency | 50 - 60 Hz |
| Power consumption (standby) | 0.5 W |
| Power consumption (typical) | 144 W |
| Compatible memory cards | SD |
| Internal storage capacity | 0.5 GB |
| Noise level | 38 dB |
| Certification | CE, CB, UL, cUL, FCC (including ICES-003), NOM, TUV-S Argentina, RoHS |
| Operating temperature (T-T) | 0 - 40 °C |
| Operating relative humidity (H-H) | 10 - 90 % |
| Cables included | VGA |
Weight and Dimensions| Weight | 1180 g |
|---|
Details regulatory compliance for the device based on FCC rules.
States compliance with Canadian ICES-003 standards.
Confirms compliance with EMC and Low Voltage Directives for Europe.
Explains how to connect the projector to a computer or notebook.
Details connecting video sources like DVD players and set-top boxes.
Step-by-step instructions for turning the projector on.
Step-by-step instructions for turning the projector off.
Explains the meaning of different LED status indicators on the projector.
Instructions on using the elevator foot to adjust image height.
How to adjust the projector's focus for a clear image.
Guidance on determining screen size and projection distance.
Describes the functions of the projector's control panel buttons.
Explains the functions of each button on the remote control.
Enables/disables input sources and selects desired ones.
Automatically selects display format or sets specific ratios like 4:3, 16:9.
Adjusts signal timing and frequency for display synchronization.
Enables or disables password verification for projector startup.
Instructions for setting or changing the security password.
Instructions for upgrading the projector's firmware.
Instructions for using MobiShow with iPhones for projection.
Instructions for using MobiShow with Android devices for projection.
Provides solutions for common projector problems.
Specific solutions for various image display issues.
Troubleshooting steps for projector-wide control issues.
Solutions for issues with USB, SD card, or media file playback.
Explains common on-screen messages and their meanings.
