Water Process Solutions Encore 700 - Page 27

ENCORE
®
700 METERING PUMP
1.
WARNING: DRIED RESIDUE OF SPILLED
30.
HYPALON TO 130°F
SOLUTIONS IS EXPLOSIVE.
31.
PVC TO 100°F, 50%, SS TO 100°F, 50%
3.
SS TO180°F
32.
PVC TO 70°F, 10%, SS TO 70°F, 10%
5.
PVC TO 125°F
34.
SS TO 70°F, 5%, PVC 125°F SAT
6.
HYPALON TO 180°F
35.
PVC TO 100°F, SS TO 70°F
7.
SS TO 125°F 10%, PVC TO 125°F
36.
VITON TO 100°F
8.
PVC TO 125°F, 29%, SS TO 180°F, 29%
37.
HYPALON TO 150°F
9.
SS TO 70°F, 5%
38.
SS TO 70°F, 10%
10.
PVC TO 105°F, 40%, SS TO 180°F SAT
39.
PVC TO 125°F, 80%, SS TO 70°F, 80%
11.
VITON TO 180°F
40.
PVC TO 100°F, SAT, SS TO 180°F, 50%
12.
PVC TO 100°F PURE
41.
SS TO 180°F, 5%
13.
VITON TO 158°F
42.
PVC TO 70°F, 50% OR TO 125°F, 30%, SS TO
14.
SS TO 140°F
180°F, 50%
15.
USE SLURRY VALVES
43.
SS TO 140°F, 10%
16.
PVC TO 105°F, SS TO 180°F
44.
SS TO 180°F, 50%
17.
PVC TO 100°F, SS TO 100°F
45.
PVC TO 105°F
18.
SS TO 70°F DILUTE, PVC TO 125°F
46.
PVC TO 125°F, 4%, SS TO 70°F, 5%
19.
PVC TO 100°F, 50%, SS TO 70°F, 5%
47.
PVC TO 125°F, 15%, SS TO 70°F, 5%
20.
PVC TO 100°F, 25%, SS TO 180°F, 50%
48.
SS TO 125°F
21.
PVC TO 100°F, SS TO 160°F
49.
PVC TO 125°F, 41 Be, SS TO 140°F, 41 Be
22.
VITON TO 120°F
50.
PVC TO 125°F, 30%
24.
PVC TO 125°F, 36%, SS TO 180°F 10%
51.
PVC TO 125°F, 50%, SS TO 70°F, 50%
25.
FLUORIDATION REQUIRES AN ANTI-SYPHON
52.
PVC TO 100°F, 10%, SS TO 150°F
PUMP INSTALLATION CONSULT LOCAL REGU-
53.
PVC TO 100°F, SS TO 180°F, 70%
LATIONS FOR DETAILS.
57.
KYNAR TO 70°F
26.
PVC TO 30%
58.
KYNAR TO 120°F
27.
PVC TO 125°F, 50%, SS TO 70°F, 5%
59.
KYNAR TO 120°F, 30%
28.
MAY CAUSE SURFACE PITTING TO SS
60.
KYNAR TO 100°F
29.
PVC TO 125°F, 48%
Statements and suggestions set forth herein are based upon the best information and practices known to WPS. However, it should not
be assumed either that information is complete on the subjects covered or that all possible circumstances, safety
measures,
precautions, etc., have been included. These statements and suggestions are not intended to reflect state, municipal, or
insurance
requirements or national safety codes; where applicable, those sources should be consulted directly. Moreover, since the conditions
of use are beyond its control, WPS makes no guarantee of results and assumes no liability in connection
with the information
contained herein.
When dealing with the installation, operation or maintenance of a specific WPS product, the manuals and data sheets pertaining to
that product should be studied carefully. In case of any doubt about a specific installation, direct inquiries to your local
WPS
representative.
CHEMICAL COMPATIBILITY OF METERING PUMPS - PERFORMANCE
440.050.190.010F
ISSUE 0 8-95
WT.440.400.001.UA.IM.1012
13