GENERAL INFORMATION
TABLE
1-1.
Specifications (Con't.)
Model
2001
External Market Input
-
Front Panel BNC connector accepts external
CW
signal
for conversion to a Birdy marker.
Input level: 100 mV
into 50 ohms
Marker Width
-
Adjustable from (approx.) 15 to 400 kHz in four steps
Marker Size
Large
-
Adjustable from (approx.) 12 V to 15 mV peak-to-peak
Small
-
Adjustable from (approx.) 50 mV to 100 uV peak-to-peak
Rectified Birdy
(for use with
X-Y
plotters)
-
Size varies with detector's impedance.
Adjustable from
(approx.)
6
V to 1 mV with detector impedance of 1 meg
ohm, or from
0.5V to 1 mV with detector impedance of
0 ohms.
Rectified birdy is positive polarity
Marker Tilt
-
Provides horizontal markers have a size equal to approxi-
mately 10% of horizontal display. Adjustment of marker
size vectorily adds the normal vertical marker to the
horizontal marker, causing the resulting marker to vary
from a horizontal position toward a vertical position.
POWER REQUIREMENTS
Line Supply 115 or 230 VAC
*lo%, 50 to 60 Hz, (approx 20 watts)
MECHANICAL SPECIFICATIONS (See Figure 1-1.)
A For total length, including knobs,
add 11/16 inch
I3
For total height, including feet,
add
518 inch
C For total width, including
screw
heads, add 3/16 inch
Weight
Net
-
19 Ibs.
Shipping
-
25
Ibs.
Figure
1-1.
1.3
OPTIONS
1.3.1
Marker A-1. Any single frequency between 1 to 1400 MHz.
1.3.2
Marker A-2.
Harmonic type at 1, 10 or 50 MHz. (Other frequencies available
on
special order.)
1.3.3
Modulator A-4. Provides 100% amplitude modulation at a 1 kHz rate.
1.3.4
Perllift
A-5. Provides contact closure during sweep time.
GENERAL
INFORMATION
Model 2001
1.3
TABLE 1-1. Specifications (Con't.)
External
Market
Input
-
Marker
Width
-
Marker Size
Large -
Small -
Rectified
Birdy
(for
use
with
X-V
plotters) -
Marker
Tilt
-
POWER
REQUIREMENTS
Line
Supply
Front
Panel BNC
connector
accepts external
CW
signal
for
conversion
to
a
Birdy
marker.
Input
level: 100
mV
into
50
ohms
Adjustable
from
(approx.) 15
to
400
kHz
in
four
steps
Adjustable
from
(approx.) 12 V
to
15
m V peak·to·peak
Adjustable
from
(approx.)
50
mV
to
100
uV
peak·to·peak
Size varies
with
detector's
impedance. Adjustable
from
(approx.) 6 V
to
1
mV
with
detector
impedance
of
1 meg
ohm,
or
from
0.5V
to
1
mV
with
detector
impedance
of
o ohms. Rectified
birdy
is
positive
polarity
Provides
horizontal
markers have a size equal
to
approxi-
mately
10010
of
horizontal
display.
Adjustment
of
marker
size
vectorily
adds the normal vertical marker
to
the
horizontal
marker, causing the resulting marker
to
vary
from
a horizontal position
toward
a vertical position.
115
or
230
VAC
±
10010,
50
to
60
Hz, (approx
20
watts)
MECHANICAL
SPECIFICATIONS
(See
Figure 1-1.)
A
For
total
length,
including
knobs,
I
[
add
11/16
inch
B
For
total
height, including feet,
TOP
add
5/8
inch
C
For
total
width,
including
screw
A~I
..
13
..
I
heads, add
3/16
inch
K[
1 G
Weight
SIDE
Net
-
191bs.
Shipping - 251bs.
Ls
C~~8~~t-C
Figure 1-1.
OPTIONS
1.3.1 Marker A-1.
Any
single frequency between 1
to
1400 MHz.
1.3.2
Marker
A-2.
Harmonic
type
at
1,
10
or
50
MHz.
(Other
frequencies available
on
special order.)
1.3.3
Modulator
A-4.
Provides 100%
amplitude
modulation
at a 1
kHz
rate.
1.3.4
Perilift
A-5. Provides
contact
closure
during
sweep time.
1-4
To Next Page
Loading...
