To Next Page
T
Thomas JonesAug 27, 2025
What causes Xerox PrimeLink B9125 Printer copies to be too light?
- RRobert KellyAug 27, 2025
If your Xerox Printer copies are consistently too light, it's likely that the copy density setting is set to Light.
What causes Xerox PrimeLink B9125 Printer copies to be too light?
If your Xerox Printer copies are consistently too light, it's likely that the copy density setting is set to Light.
Why aren't documents feeding into the document feeder of my Xerox Printer?
If documents aren't feeding into the document feeder of your Xerox Printer, it could be because the documents are too small. The minimum size of the document that can be loaded on the document feeder is A5, which is 148 x 210 mm (5.8 x 8.3 in.).
Why do I get an error message on my Xerox PrimeLink B9125 Printer after loading paper in Tray 5 (Bypass)?
If you're getting an error message after loading paper in Tray 5 (Bypass) and pressing the Start button on your Xerox Printer, the paper guides at the front of the tray might be incorrectly positioned. Make sure to set the paper guides to the correct positions.
Why does the printed toner smudge when rubbed on my Xerox prints?
If the printed toner smudges when rubbed on your Xerox prints, it could be due to a couple of reasons. The paper might be damp, so try replacing it with paper from a new ream. Alternatively, the paper you're using might be unsuitable; try loading suitable paper.
Why does a stripe pattern appear in copies from my Xerox PrimeLink B9125?
If a stripe pattern appears in copies from your Xerox Printer, the document enlargement ratio is likely set too large. Some enlargement ratios can cause stripes, so try adjusting the copy enlargement ratio.
How to fix an error message after loading paper in paper Tray 5 (Bypass) on Xerox PrimeLink B9125 Printer?
If you receive an error message after loading paper in paper Tray 5 (Bypass) and pressing the Start button, make sure that the paper guides at the front side of paper Tray 5 (Bypass) are set to the correct positions.
How to turn on Xerox Printer?
If your Xerox Printer is not powering on, there might be a few reasons. First, check if the power switch is in the off position and switch it on. Second, ensure the power cord is properly plugged into both the electrical outlet and the printer. If the power cord is disconnected, firmly plug it in and then turn the power switch on. Lastly, make sure the power supply provides the correct voltage (200-240 V, 15 A) and is compatible with the printer's maximum power consumption (2.8-3.1 KVA).
Why are black lines printed on my Xerox PrimeLink B9125 Printer copies?
If black lines are appearing on your Xerox Printer copies, the drum cartridge may be depleted or damaged, so contact Xerox Technical Customer Support. Alternatively, the document glass on the document feeder might be dirty; clean the document glass.
Why does dirt appear at equal intervals on my Xerox Printer?
If dirt appears at equal intervals on your Xerox Printer, there may be dirt on the paper feed path. Try printing a few pages to see if the issue resolves itself.
Why is nothing being printed on my Xerox Printer?
If nothing is being printed on your Xerox Printer, it could be due to a couple of reasons. Two or more sheets of paper might be feeding simultaneously (double feed); fan the paper and then reset it. Alternatively, there might be a high-voltage power supply malfunction; in this case, contact Xerox Technical Customer Support.
General instructions for safe printer operation and compliance with safety agency evaluations.
Guidelines for safe electrical connections, power cords, and emergency power off procedures.
Safe practices during printer operation, handling hot areas, and environmental considerations.
Information about Class 1 laser safety standards for North America and the European Union.
Procedures for printing documents over a network using PostScript and PCL drivers.
Step-by-step guide for making copies using the automatic document feeder.
Instructions for making copies using the document glass.
Explains various scan methods like Email, Network Scanning, Scan to PC, and Store to USB.
Step-by-step guide for sending faxes using the multifunction printer's embedded fax.
Instructions for sending faxes via email by scanning the document.
Step-by-step guide on how to register and store a program with custom settings.
General guidelines for loading, printing, and storing various types of media, including labels and glossy paper.
Procedures for cleaning the printer's exterior, touch screen, document glass, and feeder rollers.
Instructions for checking and replacing consumable supplies like toner cartridges and waste containers.
Addresses common printer issues such as no power, dark display, and unable to print.
Solutions for common image quality problems like dirty copies, skewed images, and incorrect sizing.
Instructions for clearing paper jams in various locations within the printer and feeders.
Instructions for loading paper and special media into the Standard and XLS Bypass trays.
Step-by-step guide on how to load paper into the HCF trays and adjust paper guides.
Instructions for loading paper and special media into the OHCF trays.
General