Xray XB808 - User Manual

Questions and Answers

D
David Myers MDAug 16, 2025
What to do if my Xray XB808 Motorized Toy Car engine starts but then stalls?
- E
  Elizabeth RosarioAug 16, 2025
  If your Xray Motorized Toy Car engine starts and then stalls, consider the following: * The fuel tank may be empty: fill it with fuel. * Fuel lines, fuel filter, air cleaner, or muffler could be clogged: clean or replace the clogged parts. * The carburetor might not be adjusted properly: readjust the idle and main/slow needle adjusting screw. * The engine may have overheated: allow it to cool down thoroughly and open the main needle adjusting screw 30° turn richer (CCW).
S
Stacy WilliamsAug 20, 2025
Why is my Xray XB808 hard to control?
- C
  Chad BeltranAug 20, 2025
  If your Xray Motorized Toy Car is hard to control, check these: * Weak transmitter and/or receiver batteries: recharge or replace the batteries. * Low reception from radio antennas: fully extend the transmitter and receiver antennas. * Servo linkages not adjusted properly: move the servo to neutral, then readjust the linkages.
H
Heather YoungAug 23, 2025
How to fix bad reaction and response from engine of my Xray XB808?
- A
  angela30Aug 25, 2025
  To address a bad reaction and response from the engine of your Xray Motorized Toy Car: * Readjust the main/slow needle adjusting screw if the carburetor is not adjusted properly. * Clean or replace clogged parts if fuel lines, fuel filter, air cleaner, or muffler are clogged. * Properly install the pressure line between the muffler and fuel tank if there is low fuel pressure from the muffler.
V
vsmithAug 27, 2025
What to do if steering does not work properly on my Xray Motorized Toy Car?
- D
  David WagnerAug 27, 2025
  If the steering on your Xray Motorized Toy Car isn't working correctly: * Recharge or replace weak transmitter and/or receiver batteries. * Check the tightness of steering components and tighten if necessary, in case of bent linkages or driveshafts. * Check the tightness of steering components and tighten if necessary, in case of loose steering components. * Replace damaged parts if there is drivetrain damage.
M
Miss Karen AdamsAug 31, 2025
How to troubleshoot handling problems with my Xray XB808?
- S
  santosjohnnyAug 31, 2025
  To troubleshoot handling problems with your Xray Motorized Toy Car: * Rebuild the shocks and replace worn or broken parts if the shocks are not working properly. * Ensure the suspension moves freely and replace worn or broken parts if the suspension is binding. * Use different tires if the current tires are improper.
M
Mr. Jacob DelgadoSep 4, 2025
Why does the steering feel sluggish or vague on my Xray XB808 Motorized Toy Car?
- J
  Jennifer GarciaSep 4, 2025
  If the steering on your Xray Motorized Toy Car feels sluggish or vague: * Ensure the suspension moves freely, and replace worn or broken parts if the suspension is binding. * Check the steering servo for damage and wear, and replace/repair if necessary if the steering servo is damaged.
R
Richard LopezSep 8, 2025
What to do if my Xray XB808 does not drive straight?
- M
  Mrs. Kristen Anderson MDSep 8, 2025
  If your Xray Motorized Toy Car isn't driving straight: * Ensure the suspension moves freely, and replace worn or broken parts if the suspension is binding. * Adjust steering trim until car drives straight if the steering trim is off-center. * Check and make sure the wheel nuts are properly tightened if the wheels are loose. * Check the steering servo for damage and wear, and replace/repair if necessary if the steering servo is damaged.
W
William SmithNov 11, 2025
Why won't my Xray XB808 engine start?
- U
  uosborneNov 11, 2025
  Your Xray Motorized Toy Car engine might not start due to several reasons: * The fuel tank could be empty, or the carburetor isn't primed: fill the fuel tank and prime the carburetor. * A bad glowplug or a dead glowdriver battery: replace the glowplug or recharge/replace the glowdriver battery. * Clogged fuel lines, fuel filter, air cleaner, or muffler: clean or replace the clogged parts. * The engine may be flooded due to over-priming: remove the glowplug and turn the car over to discharge fuel from the cylinder, then test and replace the glowplug if it's defective. * Improper carburetor adjustment: set the idle and main/slow needle adjusting screw to the standard starting position. * Improperly adjusted throttle servo linkage: move the throttle servo to the neutral position ...