Operator’s Manual Page 27
Menus in Detail
GLOBA
GLOBAGLOBA
GLOBAL MEM.
L MEM.L MEM.
L MEM.
Recall a Memory
Recall a MemoryRecall a Memory
Recall a Memory
Recall Graphic, Input and Crossover Memories or combinations of.
Store a Memory
Store a MemoryStore a Memory
Store a Memory
Store Graphic, Input and Crossover Memories or combinations of.
Erase a Memory
Erase a MemoryErase a Memory
Erase a Memory
Erase Graphic, Input and Crossover Memories or combinations of.
INPUT
INPUT INPUT
INPUT
SECTION
SECTIONSECTION
SECTION
Input Ganging
Input GangingInput Ganging
Input Ganging
Gang (link) inputs together so their parameters track.
Input Reset
Input ResetInput Reset
Input Reset
Start wizard to reset sections of input parameters, including graphics.
Change Graphic
Change Graphic Change Graphic
Change Graphic
Q/BW
Q/BWQ/BW
Q/BW
Select between ‘GQ600’ and other graphic behaviours.
CROSS
CROSSCROSS
CROSSOVER
OVEROVER
OVER
Design a Crossover
Design a CrossoverDesign a Crossover
Design a Crossover
Set up a new crossover from scratch. This selection starts a wizard to guide through the
process. Also select this to alter the set-up of the current crossover.
Crossover Ganging
Crossover GangingCrossover Ganging
Crossover Ganging
Gang (link) outputs together so their para
INTERFACE
INTERFACEINTERFACE
INTERFACE
External Interface
External InterfaceExternal Interface
External Interface
Starts a wizard to configure the baud rate, ID and port selection of the remote interface.
Wiser 2400 Setup
Wiser 2400 SetupWiser 2400 Setup
Wiser 2400 Setup
Configures wireless interface (if connected).
GPI Interface
GPI InterfaceGPI Interface
GPI Interface
Configure the GPI inputs used for
closed contact memory recall (hardware option).
SYSTEM
SYSTEMSYSTEM
SYSTEM
System Status
System StatusSystem Status
System Status
Displays a series of information screens including software version, temperature,
hardware and firmware versions, date and time. Press NEXT
NEXTNEXT
NEXT to jump through info.
LCD Contrast
LCD ContrastLCD Contrast
LCD Contrast
Adjust the viewing angle of the screen.
LED Brightness
LED BrightnessLED Brightness
LED Brightness
Adjust the brightness of all the meters and button LEDs.
Temperature Alarm
Temperature AlarmTemperature Alarm
Temperature Alarm
Set the threshold for the unit to flash a warning temperature message
Program Update
Program UpdateProgram Update
Program Update
Select this option to install new operating software
Wake
WakeWake
Wake-
--
-up Time
up Timeup Time
up Time
Adjust the time before the audio fades in on start
can also be set to keep mutes
when powered up.
Output Meters
Output Meters Output Meters
Output Meters
Opt’n
Opt’nOpt’n
Opt’n
Select the monitoring point for the meters
either pre or post mute (so meters can be
set to work even when outputs muted)
Filter Q/Bandwidth
Filter Q/BandwidthFilter Q/Bandwidth
Filter Q/Bandwidth
Select the readout units for the ‘Q’ setting of parametric filters
octaves) – small ‘Q’ values mean wide response variations.
Delay
Delay Delay
Delay
Time/Dist’nce
Time/Dist’nceTime/Dist’nce
Time/Dist’nce
Select the readout units for all delay values
either time, or distance in feet or metres.
Unit Cloning
Unit CloningUnit Cloning
Unit Cloning
Copy a unit’s complete setup, including mem
ories and all menu options using a PCMCIA
card. See page 38 for more information on card types.
Preset Update
Preset UpdatePreset Update
Preset Update
Load a new preset file from a PCMCIA card
Clip LED Hold
Clip LED Hold Clip LED Hold
Clip LED Hold
Time
TimeTime
Time
Select the time that the input CLIP LEDs stay illuminat
ed for after an overload has
passed.
Set Date & Time
Set Date & TimeSet Date & Time
Set Date & Time
Adjust the real time clock settings.
SECURITY
SECURITYSECURITY
SECURITY
Unit Locking
Unit LockingUnit Locking
Unit Locking
Protect the unit against unauthorised access with a password
To Next Page
Loading...
Need help?
General
