Why does “INPUT DATA ERROR” appear on the display and no sound is heard on Yamaha DSP-A1 Amplifier?
If “INPUT DATA ERROR” appears on the display of your Yamaha Amplifier and no sound is heard, the source being played may be nonstandardized, or the unit playing the source may be malfunctioning. Check the source, or turn off the unit playing back the source and then turn it on again.
Why can't DSP parameters and some other settings be changed on Yamaha Amplifier?
If you cannot change DSP parameters and some other settings on your Yamaha Amplifier, check the “9. MEMORY GUARD” function in the SET MENU mode and ensure it is set to the “OFF” position.
How to fix Yamaha DSP-A1 that won't turn on?
If your Yamaha Amplifier fails to turn on, ensure the power cord is firmly plugged into the outlet. Also, check that the IMPEDANCE SELECTOR switch on the rear panel is correctly set to either end.
Why does only one side speaker output sound on Yamaha Amplifier?
If you only hear sound from one side speaker on your Yamaha Amplifier, check the BALANCE control and adjust it to the appropriate position. Also, verify that the cord connections are correct and secure. If the issue persists, the cords may be defective.
Why does my Yamaha DSP-A1 Amplifier sound hum?
If you experience a humming sound from your Yamaha Amplifier, make sure the audio plugs are firmly connected. If the problem continues, the cords may be defective. Additionally, if you're using a turntable, ensure it is properly connected to the GND terminal on the unit.
Why is no sound heard when playing back a source (CD etc.) on Yamaha DSP-A1 Amplifier?
If no sound is heard when you play back a source (CD etc.) on your Yamaha Amplifier, even though the currently selected input mode is “AUTO”, the DTS-decoding mode may not be changing to the normal (PCM) digital signal input mode automatically. Press the INPUT MODE button on the front panel or the input selector button (for the currently selected source) on the remote control transmitter so that “PCM” appears on the display.
Why is no sound heard when playing back a source encoded with the DTS on Yamaha Amplifier?
If no sound is heard when you play back a source encoded with DTS on your Yamaha Amplifier, even though the “AUTO” or “DTS” input mode is selected, the DTS decoder built into this unit may not function because the player has a digital volume control set at a position other than “maximum”, “neutral” or “ineffective”. Set the player’s digital volume control to the maximum, neutral, or ineffective position.
Why Yamaha Amplifier remote control transmitter does not function properly?
If the remote control transmitter for your Yamaha Amplifier does not function properly, ensure that you are within a maximum range of 6 meters and no more than 30 degrees off-axis from the front panel. Also, make sure that direct sunlight or lighting is not striking the remote control sensor of the main unit. Try changing the position of the main unit. If the issue persists, the internal microcomputer may have frozen; press the RESET button on the remote control transmitter.
Why is there no sound from the center speaker on my Yamaha Amplifier?
If no sound is coming from the center speaker of your Yamaha Amplifier, first check the “1A. CENTER SP” function in the SET MENU mode and select the appropriate position. If you have selected one of the DSP programs No. 1 to No. 6 while using a 2-channel stereo (analog/PCM) input signal, select another program. If you are playing source encoded with Dolby Digital (AC-3) or DTS, refer to the source's instructions to ensure it has center channel signals.
Why is there no sound from the front effect speakers on Yamaha DSP-A1 Amplifier?
If you are not hearing sound from the front effect speakers on your Yamaha Amplifier, check the “1E. FRONT MIX” function in the SET MENU mode and ensure it is set to the “OFF-7ch” position. If you have selected PRO LOGIC/Normal, DOLBY DIGITAL/ Normal or DTS DIGITAL SUR./Normal of the DSP program No. 12, try selecting another program or subprogram.
Essential safety guidelines for operation and maintenance.
The remote control unit for operating the amplifier.
Guidance on setting up speaker systems for optimal sound.
Description of front panel buttons, knobs, and indicators.
Selecting output modes for center, rear, main, and subwoofer speakers.
Procedure to adjust speaker output levels using test tones.
How to select and use DSP sound field programs.
Guide to fine-tuning output levels for individual speakers.
Solutions for common operating problems and symptoms.
General| Surround Sound | Dolby Digital, DTS, Dolby Pro Logic |
|---|---|
| Frequency Response | 10 Hz-100 kHz +0, -3 dB |
| Total Harmonic Distortion | 0.015% |
| Signal to Noise Ratio | 96 dB |
| Output | Pre-out |
| Speaker Load Impedance | 4-16 ohms |
| Digital Inputs | Coaxial, Optical |
| Video Inputs | Composite, S-Video |
| Dimensions | 171 mm |
| Input Sensitivity | 200mV (line) |
To Next Page
