3
MW10
■ SPECIFICATIONS
Conditions MIN TYP MAX UNIT
To tal Harmonic Distortion (THD+N) 20 Hz - 20 kHz @ +14 dBu 10k ohms, GAIN
(MIC to ST OUT) controls at minimum level, all level controls at nominal level 0.1 %
Frequency Response
(CH INPUT 1-9/10, RETURN, 2TR IN to 20 Hz-20 kHz, nominal output level @ 1 kHz, 10 k ohms, -3 0 1 dB
ST OUT, AUX SEND, C-R OUT, REC GAIN controls at minimum level (CH INPUT 1-5/6), all level
OUT) controls at nominal level
Equivalent Input Noise (CH INPUT 1-2 MIC) -128 dBu
Hum & Noise Residual Output Noise (10 k ohms (ST OUT)) -100 dBu
Rs=150 ohms, Gain=Maximum (CH ST master control at nominal level and all channel LEVEL
INPUT1-2), Hum & Noise are measured controls at minimum level. (ST OUT) -87 dBu
with a -6 dB/octave filter @12.7 kHz; (91 dB S/N)
equivalent to a 20 kHz filter with infinite All channel AUX controls at minimum level. (AUX SEND) -85 dBu
dB/octave attenuation. (89 dB S/N)
ST master control and one channel LEVEL control at -64 dBu
nominal level. (CH INPUT 1, 2) (ST OUT) (68 dB S/N)
CH INPUT 1, 2 MIC to CH INSERT OUT, Rs=150 ohms, 60 dB
GAIN controls at maximum level
CH INPUT 1-5/6 MIC to ST OUT, Rs=150 ohms, 76 dB
GAIN controls at maximum level
CH INPUT 1-5/6 MIC to REC OUT, Rs=150 ohms, 64.2 dB
GAIN controls at maximum level
CH INPUT 1, 2 MIC to AUX SEND, Rs=150 ohms, 70 dB
GAIN controls at maximum level, PRE
Maximum Voltage Gain CH INPUT 1, 2 MIC to AUX SEND, Rs=150 ohms, 76 dB
1 kHz, 10k ohms GAIN controls at maximum level, POST
PAN/BAL: panned hard left or hard right. CH INPUT 3/4-5/6 LINE to ST OUT, Rs=150 ohms, 50 dB
GAIN controls at maximum level
CH INPUT 3/4-5/6 LINE to AUX SEND, Rs=150 ohms, 41 dB
GAIN controls at maximum level, PRE
CH INPUT 3/4-5/6 LINE to AUX SEND, Rs=150 ohms, 47 dB
GAIN controls at maximum level, POST
CH INPUT 7/8-9/10 to ST OUT, Rs=150 ohms, 26 dB
GAIN controls at maximum level
RETURN to ST OUT, Rs=150 ohms 12 dB
2TR IN to ST OUT, Rs=600 ohms 23.8 dB
Crosstalk (1 kHz) Adjacent inputs -70 dB
input to output -70 dB
Where 0 dBu = 0.775 Vrms
Output impedance of signal generator: 150 ohms
■ Electrical Characteristics
Monaural/Stereo CH High Pass Filter 80 Hz 12 dB/octave
Monaural/Stereo CH Equalization ±15 dB (Max. Variation)
HIGH: 10 kHz (shelving)
Turn over/roll-off frequency of shelving, MID: 2.5 kHz (peaking)
3 dB below maximumvariable level LOW: 100 Hz (shelving)
Phantom Power Supplied when Phantom +48 V switch is ON. (XLR-type input jacks)
Monaural/Stereo Input PEAK Indicator On each channel: red indicator lights if post-EQ signal (on stereo channels,
if either post-EQ signal or post-mic-amp signal) comes within 3 dB of the clipping level.
USB Audio Input/Output: 44.1/48 kHz
Included Accessories Power adaptor (PA-10), CD-ROM, USB cable
Power Consumption 19 W
Dimensions (W x H x D) 251 mm x 65 mm x 290.5 mm
Net Weight 1.8 kg
Temperature Range Operating temperature: 0 to 40°C, Storage temperature: -20 to 60°C
■ General Specifications
To Next Page
Loading...
Need help?
General
