Yealink SIP-T33P Administrator's Guide

Using Handsets with T57W/T54W/T53W/T53 Phones
131
l
Confirmation: plays when you save settings or place the handset in the charger cradle. For CP930W, you can
only configure it by navigating to Menu > Settings > Basic Settings > Sound > Advisory Tones > Confirmation.
l
Low Battery: plays when battery capacity is low and the handset requires being charged. For CP930W, you can
only configure it by navigating to Menu > Settings > Basic Settings > Sound > Advisory Tones > Low Battery.
Topic
Advisory Tones Configuration
Advisory Tones Configuration
The following table lists the parameters you can use to configure the advisory tones.
Parameter
custom.handset.keypad_tone.enable <y0000000000xx>.cfg
Description
It enables or disables the handset to play a tone when any key is pressed.
Note: It will take effect on all handsets that are registered on the same phone. It works only if “stat-
ic.auto_provision.handset_configured.enable” is set to 1 (Enabled) and the silent mode is off.
Permitted
Values
-1-Do not modify the handset configuration (Keep the original configuration of the handset).
0-Disabled
1-Enabled
Default
-1
Supported
Devices
W53H, W56H, CP930W
Handset UI
W56H/W53H:
OK > Settings > Audio > Advisory Tones > Keypad Tone
CP930W:
Menu > Settings > Basic Settings > Sound > Advisory Tones
Parameter
custom.handset.confirmation_tone.enable <y0000000000xx>.cfg
Description
It enables or disables the handset to play a tone when a user saves settings or places the handset in
the charger cradle.
Note: It will take effect on all handsets that are registered on the same phone. It works only if “stat-
ic.auto_provision.handset_configured.enable” is set to 1 (Enabled) and the silent mode is off.
Permitted
Values
-1-Do not modify the handset configuration (Keep the original configuration of the handset).
0-Disabled
1-Enabled
Default
-1
Supported
Devices
W53H, W56H, CP930W
Handset UI
W56H/W53H:
OK > Settings > Audio > Advisory Tones > Confirmation
CP930W:
Menu > Settings > Basic Settings > Sound > Confirmation
Parameter
custom.handset.low_battery_tone.enable <y0000000000xx>.cfg
Description
It enables or disables the handset to play a tone when battery capacity is low.
Note: It will take effect on all handsets that are registered on the same phone. It works only if “stat-

Yealink SIP-T33P Specifications

General

Mounting	Desk/Wall
Handset type	Wired handset
Product type	IP Phone
Product color	Gray
Wall mountable	Yes
Operating system installed	Linux
Lines quantity	4 lines
Phonebook capacity	1000 entries
Number of VoIP accounts	4
Volume control	Buttons
Number of function keys	5
Display diagonal	2.4 \
Display resolution	320 x 240 pixels
Voice codecs	AGC, AJB, CNG, G.711a, G.711u, G.722, G.723.1, G.726, G.729, G.729A, PLC, VAD, iLBC
Security algorithms	AES, HTTPS
Ethernet LAN data rates	10, 100 Mbit/s
Ethernet LAN interface type	Fast Ethernet
RJ-9 ports quantity	1
Ethernet LAN (RJ-45) ports	2
Input frequency	50/60 Hz
AC adapter input voltage	100 - 240 V
Power consumption (typical)	3 W
Power consumption (Power over Ethernet (PoE))	5 W
Number of handles included	1 pc(s)
Operating temperature (T-T)	-10 - 50 °C
Operating relative humidity (H-H)	10 - 95 %

Weight and Dimensions

Depth	186 mm
Width	212 mm
Height	146 mm