Yealink SIP-T33P Administrator's Guide

Account Settings
304
Description
It configures the registration mode in fallback mode.
Note: It is not applicable to outbound proxy servers.
Permitted
Values
0-Concurrent registration
1-Successive registration
Default
0
Parameter
account.X.fallback.timeout
[1]
<MAC>.cfg
Description
It configures the time interval (in seconds) for the phone to detect whether the working server is avail-
able by sending the registration request after the fallback server takes over call control.
Note: It is not applicable to outbound proxy servers.
Permitted
Values
Integer from 10 to 2147483647
Default
120
Parameter
account.X.outbound_proxy_fallback_interval
[1]
<MAC>.cfg
Description
It configures the time interval (in seconds) for the phone to detect whether the working outbound proxy
server is available by sending the registration request after the fallback server takes over call control.
Note: It is only applicable to outbound proxy servers.
Permitted
Values
Integer from 0 to 65535
Default
3600
Web UI
Account > Register > Proxy Fallback Interval
Phone UI
Color Screen Phones:
Menu > Advanced (default password: admin) > Accounts > Account X > Proxy Fallback Interval
Black-and-white Screen Phones:
Menu > Settings > Advanced Settings > Accounts > Proxy Fallback Interval
Parameter
account.X.redundancy_with_reg_fail.enable
[1]
<MAC>.cfg
Description
It enables or disables the phone to send the request to the next server when failing to register an
account.
Note: It works only if “account.X.fallback.redundancy_type" is set to 1 (Successive registration).
Permitted
Values
0-Disabled. Only if the working server does not respond, will the IP phone send the request to the next
server.
1-Enabled
Default
0
[1]
X is the account ID. For T57W/T54W/T48U/T48S/T48G/T46U/T46S/T46G/T29G, X=1-16; for
T53W/T53/T43U/T42G/T42U/T42S, X=1-12; for T41P/T41S/T27G, X=1-6; for T33P/T33G, X=1-4; for
T40P/T40G/T23P/T23G, X=1-3; for T31P/T31G/T31/T21(P) E2, X=1-2; for T30P/T30/T19(P) E2/CP920, X=1.
Failover Server Redundancy Configuration
The following table lists the parameters you can use to configure failover server redundancy.
Parameter
account.X.sip_server.Y.register_on_enable
[1][2]
<MAC>.cfg
Description
It enables or disables the phone to send registration requests to the secondary server when encoun-
tering a failover.
Permitted
0-Disabled, the phone will not attempt to register to the secondary server, since the phone assumes

Yealink SIP-T33P Specifications

General

Mounting	Desk/Wall
Handset type	Wired handset
Product type	IP Phone
Product color	Gray
Wall mountable	Yes
Operating system installed	Linux
Lines quantity	4 lines
Phonebook capacity	1000 entries
Number of VoIP accounts	4
Volume control	Buttons
Number of function keys	5
Display diagonal	2.4 \
Display resolution	320 x 240 pixels
Voice codecs	AGC, AJB, CNG, G.711a, G.711u, G.722, G.723.1, G.726, G.729, G.729A, PLC, VAD, iLBC
Security algorithms	AES, HTTPS
Ethernet LAN data rates	10, 100 Mbit/s
Ethernet LAN interface type	Fast Ethernet
RJ-9 ports quantity	1
Ethernet LAN (RJ-45) ports	2
Input frequency	50/60 Hz
AC adapter input voltage	100 - 240 V
Power consumption (typical)	3 W
Power consumption (Power over Ethernet (PoE))	5 W
Number of handles included	1 pc(s)
Operating temperature (T-T)	-10 - 50 °C
Operating relative humidity (H-H)	10 - 95 %

Weight and Dimensions

Depth	186 mm
Width	212 mm
Height	146 mm