Yealink SIP-T57W Administrator's Guide

Using Handsets with T57W/T54W/T53W/T53 Phones
131
l
Confirmation: plays when you save settings or place the handset in the charger cradle. For CP930W, you can
only configure it by navigating to Menu > Settings > Basic Settings > Sound > Advisory Tones > Confirmation.
l
Low Battery: plays when battery capacity is low and the handset requires being charged. For CP930W, you can
only configure it by navigating to Menu > Settings > Basic Settings > Sound > Advisory Tones > Low Battery.
Topic
Advisory Tones Configuration
Advisory Tones Configuration
The following table lists the parameters you can use to configure the advisory tones.
Parameter
custom.handset.keypad_tone.enable <y0000000000xx>.cfg
Description
It enables or disables the handset to play a tone when any key is pressed.
Note: It will take effect on all handsets that are registered on the same phone. It works only if “stat-
ic.auto_provision.handset_configured.enable” is set to 1 (Enabled) and the silent mode is off.
Permitted
Values
0-Disabled
1-Enabled
Default
1
Supported
Devices
W53H, W56H, CP930W
Handset UI
W56H/W53H:
OK > Settings > Audio > Advisory Tones > Keypad Tone
CP930W:
Menu > Settings > Basic Settings > Sound > Advisory Tones
Parameter
custom.handset.confirmation_tone.enable <y0000000000xx>.cfg
Description
It enables or disables the handset to play a tone when a user saves settings or places the handset in
the charger cradle.
Note: It will take effect on all handsets that are registered on the same phone. It works only if “stat-
ic.auto_provision.handset_configured.enable” is set to 1 (Enabled) and the silent mode is off.
Permitted
Values
0-Disabled
1-Enabled
Default
1
Supported
Devices
W53H, W56H, CP930W
Handset UI
W56H/W53H:
OK > Settings > Audio > Advisory Tones > Confirmation
CP930W:
Menu > Settings > Basic Settings > Sound > Confirmation
Parameter
custom.handset.low_battery_tone.enable <y0000000000xx>.cfg
Description
It enables or disables the handset to play a tone when battery capacity is low.
Note: It will take effect on all handsets that are registered on the same phone. It works only if “stat-
ic.auto_provision.handset_configured.enable” is set to 1 (Enabled) and the silent mode is off.
Permitted
Values
0-Disabled
1-Enabled

Yealink SIP-T57W Specifications

General

Mounting	Desk/Wall
Handset type	Wired handset
Product type	IP Phone
Product color	Gray
Ethernet LAN	Yes
Wi-Fi standards	802.11a, 802.11b, 802.11g, Wi-Fi 4 (802.11n), Wi-Fi 5 (802.11ac)
Security algorithms	AES, HTTPS, MD5, SRTP
Networking standards	IEEE 802.11a, IEEE 802.11ac, IEEE 802.11b, IEEE 802.11g, IEEE 802.11n, IEEE 802.1p, IEEE 802.1x, IEEE 802.3af
Ethernet LAN interface type	Gigabit Ethernet
Supported network protocols	FTP/TFTP/HTTP/HTTPS
Dual-Tone Multi-Frequency (DTMF) modes	In-band, Out-of band, SIP info
USB 2.0 ports quantity	1
Ethernet LAN (RJ-45) ports	2
Lines quantity	- lines
Phonebook capacity	1000 entries
Number of VoIP accounts	16
AC adapter input voltage	100 - 240 V
AC adapter output current	2 A
AC adapter output voltage	5 V
Volume control	Buttons
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 95 %
Display diagonal	7 \
Display resolution	800 x 480 pixels
Front camera	No
Cables included	LAN (RJ-45)
Number of handles included	1 pc(s)
Voice codecs	G.722, G.723.1, G.726, G.729A, G.729B, iLBC

Weight and Dimensions

Depth	220 mm
Width	259.4 mm
Height	211 mm