Yealink SIP-T57W Administrator's Guide

Advanced Features
456
Devices
Parameter
account.X.shared_line.idle_details
[1]
<y0000000000xx>.cfg
Description
It enables or disables the phone to display the basic SCA call information on the idle screen.
Note: It works only if “account.X.shared_line” is set to 1 (Shared Call Appearance).
Permitted
Values
0-Disabled
1-Enabled, users can also view the call details by long pressing the SCA line key.
Default
0
Supported
Devices
T57W, T54W, T53W, T53, T48U, T46U, T43U, T42U, T48S, T46S, T42S, T41S and T27G
[1]
X is the account ID. For T57W/T54W/T48U/T48S/T48G/T46U/T46S/T46G/T29G, X=1-16; for
T53W/T53/T43U/T42G/T42U/T42S, X=1-12; for T41P/T41S/T27G, X=1-6; for T40P/T40G/T23P/T23G, X=1-3; for T21
(P) E2, X=1-2; for T19(P) E2/CP920, X=1.
Bridge Lines Appearance (BLA)
BLA allows users to share a SIP line on two or more phones. Users can monitor the specific extension (BLA num-
ber) for status changes on each IP phone. To use this feature, a BLA group should be pre-configured on the server
and one of them is specified as a BLA number.
Yealink phones support BLA using a SUBSCRIBE/NOTIFY mechanism as specified in RFC 3265. The event used
is: “dialog” for bridged line appearance subscribe and notify.
Topic
BLA Configuration
BLA Configuration
The following table lists the parameters you can use to configure BLA.
Parameter
account.X.shared_line
[1]
<MAC>.cfg
Description
It configures the registration line type.
Permitted
Values
0-Disabled
3-Draft BLA
Default
0
Web UI
Account > Advanced > Shared Line
Parameter
account.X.bla_number
[1]
<MAC>.cfg
Description
It configures the BLA number.
Note: It works only if “account.X.shared_line” is set to 3 (Draft BLA).
Permitted
Values
String within 99 characters
Default
Blank
Web UI
Account > Advanced > BLA Number
Parameter
account.X.bla.notify_with_expire.enable
[1]
<MAC>.cfg
Description
It enables or disables the phone to add the Expires attribute to the Subscription-State header of the
BLA NOTIFY message.
Note: It works only if “account.X.shared_line” is set to 3 (Draft BLA). For teltronnic BLA, you need to set

Yealink SIP-T57W Specifications

General

Mounting	Desk/Wall
Handset type	Wired handset
Product type	IP Phone
Product color	Gray
Ethernet LAN	Yes
Wi-Fi standards	802.11a, 802.11b, 802.11g, Wi-Fi 4 (802.11n), Wi-Fi 5 (802.11ac)
Security algorithms	AES, HTTPS, MD5, SRTP
Networking standards	IEEE 802.11a, IEEE 802.11ac, IEEE 802.11b, IEEE 802.11g, IEEE 802.11n, IEEE 802.1p, IEEE 802.1x, IEEE 802.3af
Ethernet LAN interface type	Gigabit Ethernet
Supported network protocols	FTP/TFTP/HTTP/HTTPS
Dual-Tone Multi-Frequency (DTMF) modes	In-band, Out-of band, SIP info
USB 2.0 ports quantity	1
Ethernet LAN (RJ-45) ports	2
Lines quantity	- lines
Phonebook capacity	1000 entries
Number of VoIP accounts	16
AC adapter input voltage	100 - 240 V
AC adapter output current	2 A
AC adapter output voltage	5 V
Volume control	Buttons
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 95 %
Display diagonal	7 \
Display resolution	800 x 480 pixels
Front camera	No
Cables included	LAN (RJ-45)
Number of handles included	1 pc(s)
Voice codecs	G.722, G.723.1, G.726, G.729A, G.729B, iLBC

Weight and Dimensions

Depth	220 mm
Width	259.4 mm
Height	211 mm