Aastra NeXspan 500 User Manual

Integrated DECT Service
Installation guide
NeXspan C/S/L/D - NeXspan 50 - NeXspan 500
AMT/PTD/PBX/0020/2/4/EN
01/2007
© AASTRA MATRA Telecom

Aastra NeXspan 500 Specifications

General

Series	NeXspan
VoIP Support	Yes
VoIP Protocols	SIP, H.323
ISDN Support	Yes
Networking	10/100 Mbps Ethernet
Power Supply	100-240V AC, 50/60Hz

Summary

Chapter 2 - Description

2.2 DECT radio base stations

Details the physical and functional aspects of DECT base stations.

Chapter 3 - Deployment principles

3.2 Determining the radio coverage

Details the principles and methods for site survey to achieve radio coverage.

3.3 Method of determining the number of base stations according to predicted traffic

Calculates the required number of base stations based on traffic analysis.

3.5 Installing and connecting the base stations

Provides procedures for installing and connecting DECT base stations.

Chapter 4 - Implementation of hardware on NeXspan C/S/L/D

4.3 (Factory) configuration of the LD4 ST card with Stocko format

Details the factory configuration of the LD4 ST card with Stocko connectors.

4.4 (Factory) configuration of the LD4 RJ card with RJ45 format

4.5 (Factory) configuration of the LD4NX ST card with Stocko format

4.6 (Factory) configuration of the LD4NX RJ card with RJ45 format

4.8 Base station synchronization

Describes synchronization methods for DECT base stations on NeXspan S/L/D.

Chapter 5 - Implementation of hardware on NeXspan 50

5.2 Configuring the LDS card

5.3 Configuring the LDT card

5.4 synchronization

Explains synchronization procedures for NeXspan 50 with FPHBG back plane.

Chapter 6 - Implementation of hardware on NeXspan 500

6.2 Configuring the LDT card

6.2.14synchronization

Explains synchronization procedures for NeXspan 500 with FPS back plane.

Chapter 7 - Multi-site programming

7.2 Distributing DECT synchronization to the base stations

Explains methods for distributing DECT synchronization signals.

7.4 synchronization on NeXspan S/L/D with UCT-S/UCT-L/UCT-D

Details synchronization for NeXspan S/L/D using UCT cards.

7.5 synchronization on NeXspan 50 with CSI

Explains synchronization for NeXspan 50 using CSI.

Chapter 8 - Checking the installation

8.1 Preliminary operations

8.2 Procedure

Details the steps for verifying the installation and wiring.

Chapter 9 - Programming for the NeXspan C/S/L/D range

9.2 Manage topology

9.4 Putting DECT cards and base stations in service

Procedures for activating DECT interface cards and base stations.

9.5 Declaring and putting in service DECT base stations

Steps for declaring and enabling DECT base stations.

9.6 Checking the programming

9.7 Registration and putting in service

Covers registering and activating mobile terminals.

Chapter 10 - Programming for the Nexspan 50 or Nexspan 500 range

10.3 Declare the TELBOR server

10.4 Declare the radio zones

10.6 Put the cards in service

Steps to activate LDS/LDT interface cards for DECT service.

10.7 Declare the cells

10.8 Declare the DECT parameters

10.10 Declare the base stations

Declares base stations, assigning parameters and checking status.

10.12 Declare and register a mobile

Instructions for declaring and registering mobile terminals.

10.13 Declare the DECT subscribers

Chapter 11 - Multi-site programming

11.1 Precautions to be taken in a multisite configuration

11.2 Declaring the radio zones on NeXspan 50 / NeXspan 500

11.3 Programming the DECT parameters

11.4 Multi-site configuration with OCT4

Details multi-site configuration using OCT4 cards.

11.5 Multi-site configuration with UCT-S/UCT-L/IUCT-D

Describes multi-site configuration with UCT cards.

11.6 Multi-site configuration with CSI