ABB REB670 - Page 356

554 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

IEC16000071 V1 EN-US

Figure 135: Configuration with XLNPROXY and GOOSEXLNRCV where all the

IEC 61850 modelled data is used, including selection

Section 12 1MRK 505 370-UUS A

Control

350 Busbar protection REB670 2.2 ANSI

Application manual

Table of Contents

Default Chapter7
- Table of Contents7
Section 1 Introduction25
- This Manual25
- Intended Audience25
- Product Documentation26
- Document Symbols and Conventions28
  - Symbols28
  - Document Conventions29
- IEC 61850 Edition 1 / Edition 2 Mapping30
Section 2 Application41
- General IED Application41
- Main Protection Functions45
- Back-Up Protection Functions46
- Control and Monitoring Functions48
- Communication53
- Basic IED Functions55
Section 3 Configuration57
- Description of Configuration REB67057
Section 4 Analog Inputs73
- Introduction73
- Setting Guidelines73
  - Setting of the Phase Reference Channel73
    - Example74
  - Setting of Current Channels74
Section 5 Local HMI103
- Display104
- Leds107
- Keypad108
- Local HMI Functionality110
Section 6 Differential Protection113
- Busbar Differential Protection113
Section 7 Current Protection181
- Directional Phase Overcurrent Protection, Four Steps OC4PTOC(51_67)181
- Four Step Single Phase Overcurrent Protection PH4SPTOC (51)193
- Directional Residual Overcurrent Protection, Four Steps EF4PTOC (51N/67N)203
  - Identification203
  - Setting Guidelines203
- Four Step Directional Negative Phase Sequence Overcurrent Protection NS4PTOC (46I2)210
- Thermal Overload Protection, Two Time Constants TRPTTR (49)217
- Breaker Failure Protection CCRBRF(50BF)221
- Breaker Failure Protection, Single Phase Version CCSRBRF (50BF)225
- Directional Underpower Protection GUPPDUP (37)228
- Directional Overpower Protection GOPPDOP (32)234
- Capacitor Bank Protection CBPGAPC240
Section 8 Voltage Protection249
- Two Step Undervoltage Protection UV2PTUV (27)249
  - Identification249
  - Setting Guidelines249
- Two Step Overvoltage Protection OV2PTOV (59)252
- Two Step Residual Overvoltage Protection ROV2PTOV (59N)256
Section 9 Frequency Protection267
- Underfrequency Protection SAPTUF (81)267
Section 10 Multipurpose Protection273
- General Current and Voltage Protection CVGAPC273
  - Identification273
  - Application273
Section 11 Secondary System Supervision291
- Fuse Failure Supervision FUFSPVC291
- Fuse Failure Supervision VDSPVC (60)295
Section 12 Control299
- Synchronism Check, Energizing Check, and Synchronizing SESRSYN (25)299
- Autorecloser for 1 Phase, 2 Phase And/Or 3 Phase Operation SMBRREC (79)319
- Apparatus Control APC347
- Interlocking (3)367
Section 13 Logic413
- Trip Matrix Logic TMAGAPC413
- Logic for Group Alarm ALMCALH414
- Logic for Group Alarm WRNCALH414
  - Setting Guidelines415
- Logic for Group Indication INDCALH415
  - Identification415
    - Application415
- Configurable Logic Blocks415
  - Application416
  - Setting Guidelines416
    - Configuration416
- Fixed Signal Function Block FXDSIGN418
  - Identification418
  - Application418
- Boolean 16 to Integer Conversion B16I419
  - Identification419
  - Application419
- Boolean to Integer Conversion with Logical Node Representation, 16 Bit BTIGAPC420
  - Identification421
  - Application421
- Integer to Boolean 16 Conversion IB16422
  - Identification422
  - Application422
- Integer to Boolean Conversion for Six-Zone Busbar BCTZCONN423
  - Identification423
  - Application424
- Integer to Boolean 16 Conversion with Logic Node Representation ITBGAPC425
  - Identification425
  - Application425
- Elapsed Time Integrator with Limit Transgression and Overflow426
- Supervision TEIGAPC426
Section 14 Monitoring433
- Measurement433
- Logical Signal Status Report BINSTATREP463
- Limit Counter L4UFCNT464
- Running Hour-Meter TEILGAPC465
  - Identification465
  - Setting Guidelines466
Section 15 Metering467
- Pulse-Counter Logic PCFCNT467
- Function for Energy Calculation and Demand Handling ETPMMTR468
Section 16 Ethernet-Based Communication471
- Access Point471
  - Application471
  - Setting Guidelines471
- Redundant Communication473
- Merging Unit476
  - Application476
  - Setting Guidelines477
- Routes477
  - Application477
Section 17 Station Communication479
- Communication Protocols479
- IEC 61850-8-1 Communication Protocol479
Section 18 Remote Communication497
- Binary Signal Transfer497
  - Identification497
  - Application497
Section 19 Security505
- Authority Status ATHSTAT505
- Application505
- Self Supervision with Internal Event List INTERRSIG505
- Change Lock CHNGLCK506
  - Application506
- Denial of Service SCHLCCH/RCHLCCH507
  - Application507
  - Setting Guidelines508
Section 20 Basic IED Functions509
- IED Identifiers TERMINALID509
  - Application509
- Product Information PRODINF509
  - Factory Defined Settings510
- Measured Value Expander Block RANGE_XP510
- Parameter Setting Groups511
  - Setting Guidelines512
- Rated System Frequency PRIMVAL512
  - Identification512
  - Application512
- Summation Block 3 Phase 3PHSUM513
  - Application513
  - Setting Guidelines513
- Global Base Values GBASVAL513
- Signal Matrix for Binary Inputs SMBI514
- Signal Matrix for Binary Outputs SMBO515
  - Application515
  - Setting Guidelines515
- Signal Matrix for Ma Inputs SMMI515
Section 21 Requirements529
- Current Transformer Requirements529

Other manuals for ABB REB670

Operator's Manual116 pages

Commissioning Manual196 pages

Product Guide62 pages

Related product manuals

Preview: ABB REB670 Series

ABB REB670 Series

Preview: ABB REB500

Preview: ABB RET670

Preview: ABB RET615

Preview: ABB REF615

Preview: ABB REG670

Preview: ABB REG650

Preview: ABB ret650

Preview: ABB REL670

Preview: ABB RER670

Preview: ABB RED670

Preview: ABB REM615