TEMPUS. User Manual
17
- SYNC: Use the SYNC button to match the BPMs of different
decks.
Shift (Set Master): Press to set to master the deck in which it
has been pressed.
- SCRATCH ( ): Scratch mode On/Off. If Scratch mode is off
you can use the jog to modify the pitch bend.
Shift (Jog wheel lighting): Change the lighting mode of the
jog wheel.
- JOG WHEEL: Turn the jog wheel to scratch or modify the
pitch bend.
Shift (Seek): Scroll fast through of the track.
- PLAY/PAUSE: Start or stop playback.
Shift (Skip): Moves the play position to the beginning of the
loaded track.
- CUE: Skips back to the current cue point.
- CUP: Skips back to the current cue point and keeps the track
playing.
Shift (Tap): Set the tempo based on how fast or slow you tap
on the button. The tempo will be adjusted after the fourth tap.
4. LOOP
- IN: Sets the first point of one loop or the Cue point.
- OUT: Sets the final point of one loop and activates the loop.
- ACTIVE: Loop Active function On/Off. This function is
automatically activated every time that a loop has been set.
5. DECK DUPLICATE
-DELETE: This button lets you duplicate decks. In this case, if
you have any Hotcue or one loop is running, it will be also
duplicated.
6. AUTOLOOP 1/16 – 1/2
- BUTTON 1-4: Set Autoloops. Available sizes in order are 1/2,
1/4, 1/8, y 1/16 de beat.
7. AUTOLOOP 1 - 16
- PLAY BUTTONS: Set Autoloops. Available sizes in order are
1, 4, 8 y 16 beats.
8. DECKS
- DECK: No function.
9. SHIFT.
The Shift button provides a second MIDI layer for the
controller.
This function can be configured as Toggle or Hold mode. The
button is lit when Shift function is active.
10. BROWSER
- BROWSER: Turn the encoder to browse through your list of
songs/tracks. Press to enlarge the browser window.
Shift (Fast): Turn the encoder to browse through your list of
songs/tracks more quickly.
- LOAD: Load the selected track on the deck.
Shift (Load Next): Load next song of the track list into the
Deck.
- LOOP SIZE: Turn the small encoder to browse through your
list of folders. Press to expand or collapse the folders.
11. MIXER.
These controls will be operational when the MIXER STATUS
switch (1.4 Rear Panel) is in MIDI position. Otherwise, go to
1.2 Mixer Panel section to get more info about stand-alone
mixer mode.
- MASTER: Adjust the Master output level.
- BOOTH: No function.
- GAIN: Turn to adjust channel gain.
- HIGH: Turn to control the high frequencies and mute (Kill
function) them when pressed. Led will light when Kill is on.
- MID: Turn to control the mid frequencies and mute (Kill
function) them when pressed. Led will light when Kill is on.
- LOW: Turn to control the low frequencies and mute (Kill
function) them when pressed. Led will light when Kill is on.
Shift (Filter): Turn the control to adjust the FILTER parameter.
Press the control to On/Off this function.
- MONITOR CUE ( ): Pre-listen the respective channel
through the headphones output.
- 1/2 – MASTER: This switch allows you to display the Master
Output level if it is in the Master position, or channel output
level if it is in the 1/2 position.
- CHANNEL FADER: These faders let you modify the channel
volume.
- CROSSFADER: This horizontal fader lets you select the
channel that you will listen through the Master output. If
crossfader is placed in the central part the two channels will be
listened simultaneously.
- AUTO CROSSDAFER: These buttons let you shift the
Traktor crossfader automatically.
Shift (Snap ( ) & Quant ( )): Snap and Quantize mode
On/Off.
To Next Page