Interface Configuration
7750 SR OS Interface Configuration Guide Page 605
Tools Commands
aps
Syntax aps aps-id [clear]
aps mc-aps-signaling [clear]
aps mc-aps-ppp [clear]
Context tools>dump>aps
Description This command displays Automated Protection Switching (APS) information.
Parameters clear — Removes all Automated Protection Switching (APS) operational commands.
mc-aps-signaling — Displays multi-chassis APS signaling information.
mc-aps-ppp — Displays multi-chassis APS PPP information.
Sample Output
*A:AS_SR7_2# tools dump aps aps-33    
 
GrpId = 33, state = Running, mode:cfg/oper = Bi-directional/Bi-directional
   revert = 0, workPort: N/A, protPort: 2/1/1, activePort: working
   rxK1 = 0x0 (No-Req on Protect), physRxK1 = 0x0, rxK2 = 0x5
   txK1 = 0x0 (No-Req on Protect), physTxK1 = 0x0, txK2 = 0x5
   K1ReqToBeTxed = 0x0, K1ChanToBeTxed = 0x0, lastRxReq = 0xc
   MC-APS Nbr = 100.100.100.1 (Up), advIntvl = 10, hold = 30
   workPort: status = OK, Tx-Lais = None, sdCnt = 1, sfCnt = 1
     numSwitched = 1, switchSecs = 0, lastSwitched = 07/25/2007 08:00:12
     disCntTime = , alarms = , switchCmd = No Cmd 
   protPort: status = OK, Tx-Lais = None, sdCnt = 1,  sfCnt = 0
     numSwitched = 1, switchSecs = 0, lastSwitched = 07/25/2007 08:03:39
     disCntTime = , alarms = ,  switchCmd = No Cmd  
   GrpStatus: OK, mmCnt = 1, cmCnt = 1, psbfCnt = 1, feplfCnt = 2
   LocalSwitchCmd: priority = No-Req, portNum = 0
   RemoteSwitchCmd: priority = No-Req, portNum = 0
   Running Timers = mcAdvIntvl mcHold 
   processFlag =  apsFailures = , sonet = Y
   DebugInfo: dmEv = 0, dmClrEv = 0, amEv = 1, amClrEv = 1
     cmEv = 1, cmClrEv = 1, psbfEv = 1, psbfClrEv = 1
     feplfEv = 2, feplfClrEv = 2, wtrEv = 0, psbfDetectEv = 0
     wSdEv = 1, wSfEv = 2, pSdEv = 1, pSfEv = 1
     portStatusEv = 8, rxK1Ev = 9, txLaisEv = 2, lastEvName = FeplClr
     CtlUpEv = 3, CtlDnEv = 2, wAct = 0, wDeAct = 0
Seq      Event  TxK1/K2 RxK1/K2  Dir    Active         Time    
===     ======= ======= ======= =====   ======  ================
000     ProtAdd 0xc005  0x0000  Tx-->     Work  497 02:18:10.590
001     RxKByte 0xc005  0x6dea  Rx<--     Work  497 02:20:14.820
002     RxKByte 0xc005  0xc005  Rx<--     Work  497 02:21:30.970
003     RxKByte 0xc005  0x2005  Rx<--     Work  497 02:21:36.530
004      pSFClr 0x0005  0x2005  Tx-->     Work  497 02:21:40.590
005     RxKByte 0x0005  0x0005  Rx<--     Work  497 02:21:40.600