Allen-Bradley PowerFlex 70 Reference Manual

Index-3
Mounting Dimensions, 1-7
N
Notch Filter, 2-122
O
Output Contactor
Start/Stop, 2-121
Output Current, 2-124
Output Devices
Contactors, 2-121, 2-124
Output Reactor, 2-124
Output Frequency, 2-125
Output Power, 2-125
Output Reactor, 2-124
Output Voltage, 2-125
Overspeed, 2-126
Owners, 2-127
P
Parameter access level, 2-129
Parameters
Accel Mask, 2-114
Accel Owner, 2-127
Alarm x Code, 2-9
Analog In Hi, 2-12
Analog In Lo, 2-12
Analog In1 Value, 2-18
Analog In2 Value, 2-18
Analog Out Scale, 2-25
Analog Out1 Sel, 2-21
Analog Out2 Sel, 2-21
Anlg In Config, 2-6, 2-9
Anlg In Loss, 2-7
Anlg In Sqr Root, 2-16
Anlg Out Setpt, 2-26
Auto Rstrt Delay, 2-29
Auto Rstrt Tries, 2-29
Bus Reg Gain, 2-46
Bus Reg Mode A, B, 2-46
Clear Fault Owner, 2-127
Compensation, 2-152
Current Lmt Sel, 2-9, 2-160
Decel Mask, 2-114
Decel Owner, 2-127
Dig Out Setpt, 2-82
Dig Outx Level, 2-80
Dig Outx OffTime, 2-81
Dig Outx OnTime, 2-81
Digital Inx Sel, 2-62, 2-63
Digital Outx Sel, 2-8, 2-78, 2-79
Direction Mask, 2-114
Direction Owner, 2-127
Fault Clr Mask, 2-114
Fault Config x, 2-160
Feedback Select, 2-166
Flying Start En, 2-98
Flying Start Gain, 2-98
Flying StartGain, 2-98
Jog Mask, 2-114
Jog Owner, 2-127
Language, 2-111
Local Mask, 2-114
Local Owner, 2-127
Logic Mask, 2-114
MOP Mask, 2-114
MOP Owner, 2-127
PI Configuration, 2-151
PI Deriv Time, 2-150
PI Reference Sel, 2-151
Power Loss Mode, 2-132
Reference Mask, 2-114
Reference Owner, 2-127
Reset Meters, 2-154
Speed Mode, 2-166
Speed Ref A Sel, 2-7
Start Mask, 2-114
Start Owner, 2-127
Stop Owner, 2-127
Testpoint 1 Sel, 2-204
Testpoint x Data, 2-204
Torque Perf Mode, 2-205
Torque Ref x Sel, 2-209
Torque Setpoint2, 2-209
Trim Out Select, 2-151
Password, HIM, 2-107
PET Ref Wave, 2-129
PI Config, 2-137
PI Configuration, 2-151
PI Control, 2-137
PI Deriv Time, 2-150
PI Error Meter, 2-137
PI Feedback Meter, 2-137
PI Feedback Sel, 2-137
PI Integral Time, 2-137
PI Output Meter, 2-137
PI Preload, 2-137
PI Prop Gain, 2-137
PI Ref Meter, 2-137
PI Reference Sel, 2-137, 2-151
PI Setpoint, 2-137

Allen-Bradley PowerFlex 70 Specifications

General

Input Voltage	200-240V AC, 380-480V AC, 500-600V AC
Frequency Range	0 - 400 Hz
Humidity	5% to 95% non-condensing
Output Voltage	0 to Input Voltage
Control Methods	Sensorless Vector Control
Communications	Ethernet/IP, DeviceNet, ControlNet
Protection Features	Overcurrent, Overvoltage, Undervoltage, Overtemperature, Ground Fault
Operating Temperature	0°C to 50°C (32°F to 122°F)
Storage Temperature	-40°C to 70°C (-40°F to 158°F)
Enclosure Rating	IP20, NEMA Type 1