Allen-Bradley PowerFlex 750 Series Programming Manual

76 Rockwell Automation Publication 750-PM001N-EN-P - February 2017
Chapter 3 Drive Port 0 Parameters
FEEDBACK & I/O
Analog Inputs
256 Anlg In Sqrt
Analog Input Square Root
RO 16-bit
Integer
Enables/disables the square root function for each input.
257 Anlg In Loss Sts
Analog Input Loss Status
RO 16-bit
Integer
Status of the analog input loss.
260 Anlg In0 Value
Analog Input 0 Value
Value of the Analog input after filter, square root, and loss action.
Units:
Default:
Min/Max:
Volt
mA
0.000 Volts
0.000 mA
–/+10.000 Volts
0.000 / 20.000 mA
RO Real
261 Anlg In0 Hi
Analog Input 0 High
Sets the highest input value to the analog input scaling block.
Units:
Default:
Min/Max:
Volt
mA
10.000 Volts
20.000 mA
–/+10.000 Volts
0.000 / 20.000 mA
RW Real
262 Anlg In0 Lo
Analog Input 0 Low
Sets the lowest input value to the analog input scaling block.
Units
Default:
Min/Max:
Volts
mA
0.000 Volts
0.000 mA
–/+10.000 Volts
0.000 / 20.000 mA
RW Real
263 Anlg In0 LssActn
Analog Input 0 Loss Action
Selects drive action when an analog signal loss is detected. Signal loss is defined as an
analog signal less than 1V or 2mA. The signal loss event ends and normal operation
resumes when the input signal level is greater than or equal to 1.5V or 3mA.
“Ignore” (0) – No action is taken.
“Alarm” (1) – Type 1 alarm indicated.
“Flt Minor” (2) – Minor fault indicated. If running, drive continues to run.
Enable with P950 [Minor Flt Cfg]. If not enabled, acts like a major fault.
“FltCoastStop” (3) – Major fault indicated. Coast to Stop.
“Flt RampStop” (4) – Major fault indicated. Ramp to Stop.
“Flt CL Stop” (5) – Major fault indicated. Current Limit Stop.
“Hold Input” (6) – Holds input at last value.
“Set Input Lo” (7) – Sets input to P262 [Anlg In0 Lo].
“Set Input Hi” (8) – Sets input to P261 [Anlg In0 Hi].
Default:
Options:
0 = “Ignore”
0 = “Ignore”
1 = “Alarm”
2 = “Flt Minor”
3 = “FltCoastStop”
4 = “Flt RampStop”
5 = “Flt CL Stop”
6 = “Hold Input”
7 = “Set Input Lo”
8 = “Set Input Hi”
RW 32-bit
Integer
File Group
No. Display Name
Full Name
Description
Values
Read-Write Data Type
753
Options
Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Analog 0
Default0000000000000000
Bit 1514131211109876543210
0 = Square Root Disabled
1 = Square Root Enabled
753
Options
Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Loss 0 Reserved
Default0000000000000000
Bit 1514131211109876543210
0 = Loss not Present
1 = Loss Present
753
753
753
753

Allen-Bradley PowerFlex 750 Series Specifications

General

Brand	Allen-Bradley
Model	PowerFlex 750 Series
Category	Controller
Language	English