Getting Started
Rotary
encoder
:.::::
(OPEN) MUTE
~
lENT
~IESC
FISETUP
Accessory
List
• Head unit 1
• Power cable 1
• Mounting sleeve 1
• Carrying case 1
• Bracket key 2
• Screw
(MS
x 8) 4
• Remote
Control
1
• Battery (AAA size) 2
• Owner's Manual 1 set
Turning
Power
On
and
Off
Press SOURCE/<!> to turn on the unit.
• The unit can be turned on by pressing any other button except
:.::::
(OPEN).
Press and hold SOURCE/<!> for at least 2 seconds to turn
off the unit.
• Thefirst time
power
is turned on, the volume will startfrom level
12.
Detaching
and
Attaching
the
Front
Panel
Detaching
1 Turn off the unit power.
2
Press:'::::
(OPEN)
to open the front panel.
To
close the front panel, press the left side until it locks as
shown
in
the figure below.
3 Grasp the front panel firmly, slide to the left 0 ,
and then pull 8 to remove.
• The front panel may become hot in nonnal usage (especially the
connector tenninals on the back
of
the front panel). This is not a
malfunction.
•
To
protect the front panel. place it
in
the supplied carrying case.
• When detaching the front panel. do not apply excessive force
as
it
may result in malfunction.
• Do not leave the front panel open,
or
drive the
car
with the panel
open as it
may result in an accident
or
malfunction.
Attaching
1 Insert the right side
of
the front panel into the main
unit. Align the groove on the front panel with the
projections on the main unit.
2 Push the left side of the front panel until It locks
firmly into the main unit.
• Before attaching the front panel, make sure that there is no dirt
or
dust on the connector tenninals
and
no foreign object between the
front panel
and
the main unit.
• Attach the front panel carefully, holding the sides
of
the front panel to
avoidpushing buttons by mistake.
Initial
System
Start-Up
Be sure to press the RESET switch when using the unit for the first
time, after changing the car battery, etc.
1 Turn off the unit power.
2
Press:'::::
(OPEN)
to open the front panel, and then
remove it.
3 Press
RESET
with a ballpoint pen
or
similar pointed
object.
~
I
=.
I
RESET
switch
7-EN
Getting Started
Rotary
encoder
:.::::
(OPEN) MUTE
~
lENT
~IESC
FISETUP
Accessory
List
• Head unit 1
• Power cable 1
• Mounting sleeve 1
• Carrying case 1
• Bracket key 2
• Screw
(MS
x 8) 4
• Remote
Control
1
• Battery (AAA size) 2
• Owner's Manual 1 set
Turning
Power
On
and
Off
Press SOURCE/<!> to turn on the unit.
• The unit can be turned on by pressing any other button except
:.::::
(OPEN).
Press and hold SOURCE/<!> for at least 2 seconds to turn
off the unit.
• Thefirst time
power
is turned on, the volume will startfrom level
12.
Detaching
and
Attaching
the
Front
Panel
Detaching
1 Turn off the unit power.
2
Press:'::::
(OPEN)
to open the front panel.
To
close the front panel, press the left side until it locks as
shown
in
the figure below.
3 Grasp the front panel firmly, slide to the left 0 ,
and then pull 8 to remove.
• The front panel may become hot in nonnal usage (especially the
connector tenninals on the back
of
the front panel). This is not a
malfunction.
•
To
protect the front panel. place it
in
the supplied carrying case.
• When detaching the front panel. do not apply excessive force
as
it
may result in malfunction.
• Do not leave the front panel open,
or
drive the
car
with the panel
open as it
may result in an accident
or
malfunction.
Attaching
1 Insert the right side
of
the front panel into the main
unit. Align the groove on the front panel with the
projections on the main unit.
2 Push the left side of the front panel until It locks
firmly into the main unit.
• Before attaching the front panel, make sure that there is no dirt
or
dust on the connector tenninals
and
no foreign object between the
front panel
and
the main unit.
• Attach the front panel carefully, holding the sides
of
the front panel to
avoidpushing buttons by mistake.
Initial
System
Start-Up
Be sure to press the RESET switch when using the unit for the first
time, after changing the car battery, etc.
1 Turn off the unit power.
2
Press:'::::
(OPEN)
to open the front panel, and then
remove it.
3 Press
RESET
with a ballpoint pen
or
similar pointed
object.
~
I
=.
I
RESET
switch
7-EN
To Next Page
Loading...
