No
Disc
• No CD is inserted.
- Insert a CD.
• Although a disc is inserted,
"No
Disc" is displayed and the unit
does not start
to
play or eject the disc.
- Remove the disc
by
following these steps:
Press the
~
button again for at least 2 seconds.
If
the disc still does not eject, consult your Alpine dealer.
Error
• Mechanism error.
I) Press the
~
bunon and eject the CD.
If not ejecting, consult your Alpine dealer.
2) When the error indication remains after ejecting, press the
~
bunon again.
If the error indication still does not tum offafter pressing the
~
button for a
few
times, consult your Alpine dealer.
• When "Error" is displayed:
Ifthe disc cannot be ejected by pressing
~.
press the
RESET
switch
(refer
10 page
7)
and
press
~
again.
If
the disc still cannot be ejected. consult yourAlpine dealer.
PROTECT
• A copy-protected WMA file was played back.
-
You
can only play back non-copy-protected files.
I
UNSUPPORTED
I
• A sampling ratelbit rate not supported
by
the unit is used.
- Use a sampling ratelbit rate that is supported
by
the unit.
Error 02
• A disc
is
left inside the CD Changer.
- Press the eject button
to
activate the eject function. When the
CD Changer finishes the eject function, insert an empty CD
magazine into the CD Changer to receive the disc left inside
the CD Changer.
No
Magazine
• No magazine is loaded into the CD Changer.
- Insert a magazine.
No
Disc
• No indicated disc.
- Choose another disc.
ANTENNA
• The
XM
or SIRIUS antenna is not connected to the
XM
or
SIRIUS radio module.
- Check whether the XM or SIRIUS antenna cable is attached
securely to the
XM
or SIRIUS radio module.
UPDATING I
• Radio is being updated with latest encryption code.
- Wait until encryption code is being updated. Channels 0 and I
should function normally.
LOADING
•
XM
or SIRIUS signal is too weak at the current location.
- Wait until the car reaches a location with a stronger signal.
• Radio is acquiring audio or program information.
- Wait until the radio has received the information.
• The channel currently selected has stopped broadcasting.
- Select another channel.
HighTemperature
• Protective circuit is activated due to high temperature.
- The indication will disappear when the temperature returns to
normal operating range.
Error
01
• Malfunction
in
the CD Changer.
- Consult your Alpine dealer. Press the magazine eject bunon and
pull out the magazine.
Check the indication. Insert the magazine again.
If the magazine cannot be pulled out, consult your Alpine
dealer.
• Magazine ejection not possible.
- Press the magazine eject button.
If
the magazine does not eject,
consult your Alpine dealer.
I
NO
SIGNAL I
I
Acquiring
Signal
I
OFF
AIR
Acquiring
Signal
(XM mode)
(SIRIUS mode)
(XM mode)
(SIRIUS mode)
41-EN
No
Disc
• No CD is inserted.
- Insert a CD.
• Although a disc is inserted,
"No
Disc" is displayed and the unit
does not start
to
play or eject the disc.
- Remove the disc
by
following these steps:
Press the
~
button again for at least 2 seconds.
If
the disc still does not eject, consult your Alpine dealer.
Error
• Mechanism error.
I) Press the
~
bunon and eject the CD.
If not ejecting, consult your Alpine dealer.
2) When the error indication remains after ejecting, press the
~
bunon again.
If the error indication still does not tum offafter pressing the
~
button for a
few
times, consult your Alpine dealer.
• When "Error" is displayed:
Ifthe disc cannot be ejected by pressing
~.
press the
RESET
switch
(refer
10 page
7)
and
press
~
again.
If
the disc still cannot be ejected. consult yourAlpine dealer.
PROTECT
• A copy-protected WMA file was played back.
-
You
can only play back non-copy-protected files.
I
UNSUPPORTED
I
• A sampling ratelbit rate not supported
by
the unit is used.
- Use a sampling ratelbit rate that is supported
by
the unit.
Error 02
• A disc
is
left inside the CD Changer.
- Press the eject button
to
activate the eject function. When the
CD Changer finishes the eject function, insert an empty CD
magazine into the CD Changer to receive the disc left inside
the CD Changer.
No
Magazine
• No magazine is loaded into the CD Changer.
- Insert a magazine.
No
Disc
• No indicated disc.
- Choose another disc.
ANTENNA
• The
XM
or SIRIUS antenna is not connected to the
XM
or
SIRIUS radio module.
- Check whether the XM or SIRIUS antenna cable is attached
securely to the
XM
or SIRIUS radio module.
UPDATING I
• Radio is being updated with latest encryption code.
- Wait until encryption code is being updated. Channels 0 and I
should function normally.
LOADING
•
XM
or SIRIUS signal is too weak at the current location.
- Wait until the car reaches a location with a stronger signal.
• Radio is acquiring audio or program information.
- Wait until the radio has received the information.
• The channel currently selected has stopped broadcasting.
- Select another channel.
HighTemperature
• Protective circuit is activated due to high temperature.
- The indication will disappear when the temperature returns to
normal operating range.
Error
01
• Malfunction
in
the CD Changer.
- Consult your Alpine dealer. Press the magazine eject bunon and
pull out the magazine.
Check the indication. Insert the magazine again.
If the magazine cannot be pulled out, consult your Alpine
dealer.
• Magazine ejection not possible.
- Press the magazine eject button.
If
the magazine does not eject,
consult your Alpine dealer.
I
NO
SIGNAL I
I
Acquiring
Signal
I
OFF
AIR
Acquiring
Signal
(XM mode)
(SIRIUS mode)
(XM mode)
(SIRIUS mode)
41-EN
To Next Page
Loading...
