Alpine CDA-9886 - Page 68

Installation
2
Hex Nut (M5) Screw
Air ventilation hole
Metal
Mounting
Strap
Ground Lead
Slide the CDA-9886 into the dashboard until it clicks.
This ensures that the unit Is properly locked and will
not accidentally come out from the dashboard.
Removal
1. Remove the detachable front panel.
2. Insert the bracket keys into the unit, along the guides
on either side. The unit can now be removed from the
mounting sleeve.
3
~D
_::~Mr·R
Front Frame
<JAPANESE CAR>
This unit
~. . ~ Bracket keys
~' ~ (Included)
~
3. Pull the unit out, keeping it unlocked as you do so.
Chassis
Reinforce the head unit with the metal mounting
strap (not supplied). Secure the ground lead of the
unit to a clean metal spot using a screw
(*1) already
attached to the vehicle's chassis.
• For the screw marked ",.2 ", use an appropriate screw for the chosen
mounting location.
Connect each input lead coming from an amplifier or
equalizer to the corresponding output lead coming
from the left rear of the CDA·9886. Connect all other
leads of the CDA-9886 according to details
described in the CONNECTIONS section.
Dashboard
This unit
Mounting Sleeve
(InclUded)
Lou,",,"" ;-;~
1 a: ..... J---
Pressure Plates·
Caution
When you install this unit in your car, do not remove the
detachable front panel. .
If the detachable front panel is removed during installation, you
might press too hard and warp the metal plate that holds it in
place.
Caution
Do not block the unit'sfan or heat sink, thus preventing air
circulation. If blocked, heat will accumulate inside the unit and
may cause afire.
• The main unit must be mounted within
35 degrees of the horizontal
plane, back
to front.
1
• If the installed mounting sleeve is loose in the dashboani, the
pressure plates may be bent slightly
to remedy the problem. This unit
Remove the mounting sleeve from the main unit
(see "Removal" on page 45).
Scraws (M5 x 8)
(Included)
• Secure the ground lead of the unit to a clean metal spot using a
screw (,.3) already attached to the vehicle's chassis.
45-EN
Installation
2
Hex Nut (M5) Screw
Air ventilation hole
Metal
Mounting
Strap
Ground Lead
Slide the CDA-9886 into the dashboard until it clicks.
This ensures that the unit Is properly locked and will
not accidentally come out from the dashboard.
Removal
1. Remove the detachable front panel.
2. Insert the bracket keys into the unit, along the guides
on either side. The unit can now be removed from the
mounting sleeve.
3
~D
_::~Mr·R
Front Frame
<JAPANESE CAR>
This unit
~. . ~ Bracket keys
~' ~ (Included)
~
3. Pull the unit out, keeping it unlocked as you do so.
Chassis
Reinforce the head unit with the metal mounting
strap (not supplied). Secure the ground lead of the
unit to a clean metal spot using a screw
(*1) already
attached to the vehicle's chassis.
• For the screw marked ",.2 ", use an appropriate screw for the chosen
mounting location.
Connect each input lead coming from an amplifier or
equalizer to the corresponding output lead coming
from the left rear of the CDA·9886. Connect all other
leads of the CDA-9886 according to details
described in the CONNECTIONS section.
Dashboard
This unit
Mounting Sleeve
(InclUded)
Lou,",,"" ;-;~
1 a: ..... J---
Pressure Plates·
Caution
When you install this unit in your car, do not remove the
detachable front panel. .
If the detachable front panel is removed during installation, you
might press too hard and warp the metal plate that holds it in
place.
Caution
Do not block the unit'sfan or heat sink, thus preventing air
circulation. If blocked, heat will accumulate inside the unit and
may cause afire.
• The main unit must be mounted within
35 degrees of the horizontal
plane, back
to front.
1
• If the installed mounting sleeve is loose in the dashboani, the
pressure plates may be bent slightly
to remedy the problem. This unit
Remove the mounting sleeve from the main unit
(see "Removal" on page 45).
Scraws (M5 x 8)
(Included)
• Secure the ground lead of the unit to a clean metal spot using a
screw (,.3) already attached to the vehicle's chassis.
45-EN