Alstom MiCOM P546 - Page 431

Operation P54x/EN OP/B94
MiCOM P543, P544, P545, P546 (OP) 5-259
OP
CSRef
Check Synch
Check synch settings
and operation criteria
are shown
1
Setting:
Select
A-N,B-N,C-N
A-B,B-C,C-A
DDB:CB1 CS1 OK(883)
DDB:CB1 CS1 Enabled(881)*
DDB:CB1 CS2 Enabled(882)*
DDB: CSVLine>(1581)
DDB: CSVBus1>(1583)
DDB: CB1 CS1 VL>VB(1586)
DDB: CB1 CS1 VL<VB(1588)
DDB: CB1 CS1 FL>FB(1590)
DDB: CB1 CS1 FL<FB(1591)
&
DDB: CB1 CS1SlipF>(1578)
DDB: CB1 CS1SlipF<(1579)
DDB: CB1 CS2SlipF>(1464)
DDB: CB1 CS2SlipF<(1465)
DDB: CSVline<(1580)
DDB: CSVBus1<(1582)
DDB: CB1 CS2 FL>FB(1493)
DDB: CB1 CS2 FL<FB(1494)
DDB: CB1 CS2AngHigh+(1495)
DDB: CB1 CS2AngHigh-(1496)
DDB: CB1 CS AngRotACW(1594)
DDB: CB1 CS AngRotCW(1595)
DDB: CB1 CS1AngHigh+(1592)
DDB: CB1 CS1AngHigh-(1593)
&
&
&
&
&
&
&
&
&
&
&
&
&
&
&
&
&
&
&
CB1 CS1SlipF>
CB1 CS1SlipF<
CB1 CS2SlipF>
CB1 CS2SlipF<
CSVline<
CSVBus1<
CSVLine>
CSVBus1>
CB1 CS1VL>VB1
CB1 CS1VL<VB1
CB1 CS1FL>FB1
CB1 CS1FL<FB1
CB1 CS1AngHigh+
CB1 CS1AngHigh-
CB1 CS2FL>FB1
CB1 CS2FL<FB1
CB1 CS2AngHigh+
CB1 CS2AngHigh-
CS1AngRotACW
CS1AngRotCW
DDB: CB1 CS2 VL>VB(1587)
DDB: CB1 CS2 VL<VB(1589)
&
&
CB1 CS2VL>VB1
CB1 CS2VL<VB1
&
&
Setting:
System Checks CB1:
Enabled/Disabled
Enabled
Disabled
DDB:SchkslnactiveCB1(880)
Setting:
CB1 CS1:
Enabled/Disabled
Enabled
Disabled
&
Setting:
CB1 CS2:
Enabled/Disabled
Enabled
Disabled
&
BUS1 VT
LINE VT
CS1
Inputs default to high if
unmapped in PSL
CB1 CS1CriteriaOK
CB1 CS2CriteriaOK
DDB:CB1 CS2 OK(884)
ConfigurationSetting:
System Checks:
Enabled/Disabled
Enabled
Disabled
1
&
DDB: MCB/VTS(438)
DDB: MCB/VTSCS1(1521)
DDB: F Out of Range(319)
Fig 60
DDB: VTS Fast Block(832)
*Note
If not mapped in PSL
are defaulted high.
Figure 60 CB1 synch check signals