AUMA SAExC 16.1 - Page 3

Page
7.1.1 Status indication S0/S6 - operation 34
7.1.2 Status indication S4 - torque 35
7.2. Indication lights/LEDs 36
7.3. Mechanical position indicator/running indication (option) 36
8. Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
8.1. Signals via fieldbus 37
8.2. Feedback via output contacts (binary) - (option) 37
8.3. Feedback signals (analogue) - (option) 37
9. Commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
9.1. Type of seating: check/edit for end positions 39
9.2. Torque switching: check/set 42
9.3. Limit switching setting 45
9.4. Bus address setting (slaveaddress) 48
9.5. Test run 51
9.5.1 Rotational direction check 51
9.5.2 Limit switching check 52
9.6. Switch compartment: open 53
9.7. Mechanical position indicator setting (option) 53
9.8. Gear stage of the reduction gearing: test/set 54
9.9. Switch compartment: close 56
10. Corrective action . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
10.1. Faults during commissioning 57
10.1.1 Mechanical position indicator 57
10.1.2 Fault in end position (overrun not considered) 57
10.1.3 Push buttons do not react 57
10.2. Fault indications and warning indications 58
10.2.1 Status display S0 - faults and warnings 58
10.2.2 Status indication S1 - faults 59
10.2.3 Status indication S2 - warnings 60
10.2.4 Status indication S3 - causes for not ready remote 62
10.3. Fuses 63
10.3.1 Fuses within the actuator controls 63
10.3.2 Motor protection (thermal monitoring) 64
11. Servicing and maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
11.1. Preventive measures for servicing and safe operation 65
11.2. Disconnection from the mains 66
11.3. Maintenance 67
11.4. Disposal and recycling 68
12. Spare parts list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
12.1. Multi-turn actuator SAExC 07.1 – SAExC 16.1/SARExC 07.1 – SARExC 16.1 70
12.2. Controls ACExC 01.1 with ex-plug/socket connector with terminal board (KP, KPH) 72
12.3. Controls ACExC 01.1 with ex-plug-in terminal connection (KES) 74
13. Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
14. Certificates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
14.1. Declaration of Conformity and Declaration of Incorporation 81
14.2. PTB certificate 82
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85
Addresses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
3
Multi-turn actuator SAExC 07.1 – SAExC 16.1/SARExC 07.1 – SARExC 16.1
Non-Intrusive
Operation instructions with actuator controls AUMATIC ACExC 01.1 Profibus DP