FBXXX Field Temperature Block
Commands by Function or Group
46
SCREEN
PARAMETER Command
Password Protection
Group Read/Write
Calibration – Heat Source TEMP 1 SOUR:SENS:CAL:PAR1 Unconditional R/W
TEMP 2 SOUR:SENS:CAL:PAR2 Unconditional R/W
TEMP 3 SOUR:SENS:CAL:PAR3 Unconditional R/W
GRAD 1 SOUR:SENS:CAL:GRAD1 Unconditional R/W
GRAD 2 SOUR:SENS:CAL:GRAD2 Unconditional R/W
GRAD 3 SOUR:SENS:CAL:GRAD3 Unconditional R/W
GRAD 4 SOUR:SENS:CAL:GRAD4 Unconditional R/W
GRAD 5 SOUR:SENS:CAL:GRAD5 Unconditional R/W
TEMP 1 SOUR:SENS:CAL:TEMP1 N/A R
TEMP 2 SOUR:SENS:CAL:TEMP2 N/A R
TEMP 3 SOUR:SENS:CAL:TEMP3 N/A R
Calibration – Reference
(-R model only)
REF1C0 SENS1:CAL:PAR1 Unconditional R/W
REF1C100 SENS1:CAL:PAR2 Unconditional R/W
INPUT CAL DATE CAL:DATE:MOD Unconditional R/W
Main Screen (none) SOUR:SENS:DATA N/A R
SETPT SOUR:SPO N/A R/W
STAB SOUR:STAB:DAT N/A R
STAB graph SOUR:STAB:TEST N/A R
HEAT % OUTP1:DATA N/A R
(none) OUTP2:DATA N/A R
ENABLE OUTP1:STAT N/A R/W
(-R model only) REF CALC1:DATA N/A R
(-R model only) REF TEMP READ, MEAS, FETC N/A R
Program – Run TEST STATUS PROG:STAT N/A R/W
Program - List (none) PROG:CAT N/A R
Program - Select (none) PROG:TYP N/A R/W
Program - Setup TEST ID PROG:IDEN N/A R/W
(none) PROG:MEM:COUN N/A R
Erase Tests ERASE TESTS PROG:MEM:CLEA Unconditional W
Ramp & Soak RAMP/SOAK SETUP PROG:SEQ:CAT N/A R
SETPOINT n PROG:SEQ:PAR SPOn Conditional R/W
SOAK TIME PROG:SEQ:PAR DWEL Conditional R/W
SETPOINTS PROG:SEQ:PAR POIN Conditional R/W
NO CYCLES PROG:SEQ:PAR CYCL Conditional R/W
PASS TOLERANCE PROG:SEQ:PAR PTOL Conditional R/W
DIRECTION PROG:SEQ:PAR DIR Conditional R/W
SETPOINT 1 SOUR:LIST:SPO1 N/A R/W
SETPOINT 2 SOUR:LIST:SPO2 N/A R/W
SETPOINT 3 SOUR:LIST:SPO3 N/A R/W
SETPOINT 4 SOUR:LIST:SPO4 N/A R/W
SETPOINT 5 SOUR:LIST:SPO5 N/A R/W
SETPOINT 6 SOUR:LIST:SPO6 N/A R/W
SETPOINT 7 SOUR:LIST:SPO7 N/A R/W
SETPOINT 8 SOUR:LIST:SPO8 N/A R/W
Test – Results (-R model
only)
PRINT TEST PROG:MEM:PRINT N/A W
ERASE TESTS PROG:MEM:CLEA Unconditional W
To Next Page
Loading...
