BMW M54 User Manual

2004
-
2006 ENGINE
Engine Mechanical - Repair Instructions - X3 & X5 (M54)
ENGINE GENERAL
00 00 250 BMW ENGINE OIL SERVICE (M54/56)
Recycling:
Catch and dispose of used oil in a suitable container.
Observe country-specific waste-disposal regulations.
Undo oil filter cap (36 A/F).
Fig. 1: Identifying Oil Filter Cap (36 A/F)
Courtesy of BMW OF NORTH AMERICA, INC.
2006 BMW X5 30i
2004-2006 ENGINE Engine Mechanical - Repair Instructions - X3 & X5 (M54)
2006 BMW X5 30i
2004-2006 ENGINE Engine Mechanical - Repair Instructions - X3 & X5 (M54)
sábado, 2 de octubre de 2021 11:25:50 p. m. Page 1 © 2011 Mitchell Repair Information Company, LLC. sábado, 2 de octubre de 2021 11:26:00 p. m. Page 1 © 2011 Mitchell Repair Information Company, LLC.

BMW M54 Specifications

General

Brand	BMW
Model	M54
Category	Automobile
Language	English

Summary

ENGINE GENERAL

BMW ENGINE OIL SERVICE (M54/56)

Procedure for engine oil service, including recycling and filter cap removal.

CHECKING COMPRESSION OF ALL CYLINDERS (M60 / M62 / M73 / S62 / M54)

REMOVING AND INSTALLING ENGINE (M54)

CYLINDER HEAD WITH COVER

REMOVING AND INSTALLING, SEALING CYLINDER HEAD COVER (M52TU / M54 / M56)

Steps for removing and installing the cylinder head cover, including ignition coil and wiring harness removal.

REMOVING AND INSTALLING/REPLACING CYLINDER HEAD (M52TU / M54 / M56)

REPLACING CYLINDER HEAD GASKET (M52 / S52 / M52TU / M54 / M56)

DISASSEMBLING AND ASSEMBLING CYLINDER HEAD (M52 / S52 / M52TU / M54 / M56)

Procedures for disassembling and assembling the cylinder head, including special tools.

OIL SUMP

REMOVING AND INSTALLING, SEALING OR REPLACING OIL SUMP (M52TU / M54 / M56)

Steps for oil sump removal, installation, and sealing.

HOUSING COVER

REMOVING AND INSTALLING LOWER TIMING CASE COVER (M52 / S52 / M52TU / M54)

Procedures for removing and installing the lower timing case cover.

CRANK SHAFT WITH BEARING

REPLACING CRANKSHAFT (M52 / S52 / M52TU / M54 / M56)

Steps for replacing the crankshaft, including preliminary tasks.

FLYWHEEL

REMOVING AND INSTALLING OR REPLACING FLYWHEEL (M52 / S52 / M52TU / M54 / S54)

Procedures for removing, installing, and replacing the flywheel.

VIBRATION DAMPER (M52TU / M54 / M56)

REMOVING AND INSTALLING OR REPLACING VIBRATION DAMPER (M52TU / M54 / M56)

Steps for removing, installing, and replacing the vibration damper.

CONNECTING ROD WITH BEARINGS

REPLACING ALL CONNECTING ROD BEARINGS (M52 / S52 / M52TU / M54 / M56)

PISTON WITH RINGS AND PIN

REMOVING AND INSTALLING OR REPLACING ALL PISTONS (M52 / S52 / M52TU / M54 / M56)

V-RIBBED BELT

REPLACING ALTERNATOR DRIVE BELT (M52 / S52 / M52TU / M54 / M56)

CAMSHAFT

REPLACING CAMSHAFT (M52TU / M54 / M56)

VARIABLE CAMSHAFT TIMING

REMOVING AND INSTALLING OR REPLACING DOUBLE VANOS ADJUSTMENT UNIT (M52TU / M54 / M56)

Procedures for removing, installing, and replacing the double VANOS adjustment unit.

OIL FILTER AND LINES

REMOVING AND INSTALLING COMPLETE FULL-FLOW OIL FILTER (M52 / S52 / M52TU / M54 / M56)

OIL FILLING, DIPSTICK

REMOVING AND INSTALLING/REPLACING OIL DIPSTICK (M54/56)

WATER PUMP WITH DRIVE

REMOVING AND INSTALLING COMPLETE WATER PUMP (M52 / S52 / M52TU / M54 / M56)

THERMOSTAT AND CONNECTIONS

REMOVING AND INSTALLING/REPLACING COOLANT THERMOSTAT (M52TU / M54 / M56)

INTAKE MANIFOLD

REMOVING AND INSTALLING INTAKE AIR MANIFOLD (M54)

EXHAUST MANIFOLD

REMOVING AND INSTALLING/REPLACING BOTH EXHAUST MANIFOLDS WITH CATALYTIC CONVERTER (M54 X3)

EMISSION CONTROL, OXYGEN SENSORS

REPLACING OXYGEN CONTROL SENSOR (M52TU / M54 / M56)

POSITIVE CRANKCASE VENTILATION/OIL SEPARATOR COMPONENTS