15
Bosch Security Systems 09/06 BLCC100R
Solution 16
plus
Quick Start Guide
Me nu Re ference Tab le
The Solution Controller includes a simple text menu system which makes all levels of programming extremely easy. Once
a valid PIN has been entered followed by the MENU key the system will automatically determine which menus and option
the user has access to and only those items will be displayed.
There are four basic grouping levels used;
A = All (No PIN Required)
U = User PIN Has Access
M = Master PIN Has Access
I = Installer PIN Has Access
The following table lists all programming menus and the authority level required to access them.
0 Commands 1 Access 2 Areas
UMI 2-0-1 Turn Area On/Off 1-0 Commands 2-0 Commands
UMI 2-0-2 Turn All Areas On MI 1-0-0 Erase User AUMI 2-0-0 Area Status
UMI 2-0-3 Turn All Areas Off UMI 2-0-1 Turn Area On/Off
UMI 2-0-4 Move To Area 1-1 PIN Codes UMI 2-0-2 Turn All Areas On
AUMI 2-0-5 Chime On/Off UMI 1-1-0 Change Own PIN UMI 2-0-3 Turn All Areas Off
UMI 1-1-0 Change Own PIN M 1-1-1 Change Other PIN UMI 2-0-4 Move To Area
AUMI 3-0-0 Zone Status MI 1-1-2 Add PIN AUMI 2-0-5 Chime On/Off
AUMI 4-0-0 Output Status MI 1-1-3 Delete PIN UMI 2-0-6 Chime Mode
UMI 4-0-1 Turn Output On/Off I 1-1-4 View PIN
MI 7-1-0 Set Date & Time 2-1 Area Properties
UMI 3-0-5 Smoke Sensor Reset 1-2 Token MI 2-1-0 Area Name
UMI 3-9-0 Walk Test All Zones MI 1-2-0 Add Token I 2-1-1 General Options
MI 4-9-0 External Siren Test MI 1-2-1 Delete Token I 2-1-2 Input Options
MI 4-9-1 Internal Siren Test MI 1-2-2 Token Status I 2-1-3 Output Options
MI 4-9-2 Strobe Test I 2-1-4 Reporting Options
MI 5-0-0 Set Domestic Number 1-3 RF Keyfob I 2-1-5 Strobe Trigger
UMI 5-0-1 Call/Answer RAS MI 1-3-0 Add Keyfob
UMI 7-9-1 Battery Test MI 1-3-1 Delete Keyfob 2-2 Reporting
UMI 5-9-0 Test Dialler I 1-3-2 Test Keyfob I 2-2-0 Account Dest 1
I 7-0-8 Service Mode I 2-2-1 Account Dest 2
UMI About 1-4 User Properties I 2-2-2 Open Close Route
MI 1-4-0 User Name
MI 1-4-1 Area Assignment 2-9 Area Testing
I 1-4-2 User Options I 2-9-0 Area Watch
MI 1-4-4 Timer Group I 2-9-1 User Test Interval
MI 1-4-5 Access Assignment I 2-9-2 Service Interval
I 2-9-3 Test Options
I 1-5 Global Properties
I 1-5-0 PIN Length
I 1-5-1 PIN Retry Count
I 1-5-2 Installer PIN
I 1-5-3 PIN Expire Time
I 1-6 Prox Reader
I 1-6-0 Name
I 1-6-1 Area Assignment
I 1-6-2 Access Group
I 1-6-3 Reader Options