19
Bosch Security Systems 09/06 BLCC100R
Solution 16
plus
Quick Start Guide
Access > Global Properties >
PIN Length
MENU 1-5-0
0 = Variable 4
1 = 1 Digit 4 = 4 Digits 7 = 7 Digits
2 = 2 Digits 5 = 5 Digits 8 = 8 Digits
3 = 3 Digits 6 = 6 Digits
Enter 0 - 15 + [OK] To Program The PIN Length Option.
(*** System Wide Parameter ***)
Access > Global Properties >
PIN Retry Count
MENU 1-5-1
(*** System Wide Parameter ***)
6
Use Keys [] and [] keys or enter 0 – 8 + [OK] To Program The PIN
Retry Count (0 = Unlimited).
Access > Global Properties >
Installer PIN
MENU 1-5-2
1 2 3 4
Use Digits 0 – 9 To Program The Installer PIN + [OK] To Save. Installer
PIN Can Be Up To 8 Digits Long.
(*** System Wide Parameter ***)
Access > Global Properties >
PIN Expire Time
MENU 1-5-3
0 3 0
(*** System Wide Parameter ***)
DAYS
Enter Digits 0 – 255 + [OK] To Program How Many Days A Temporary
PIN Is Valid.
Access > Prox Reader >
Name
MENU 1-6-0
R e a d e r 1 N a m e
Use [] and [] Keys To Scroll Cursor Left and Right. Use Keys [0]
– [9] + [#] and [*] To Toggle Characters + Enter [OK] To Save
Access > Prox Reader >
Area Assignment
MENU 1-6-1
1
Use Keys [] and [] keys or enter 1 - 4 (0 = Not Assigned) To Assign
The Reader To An Area, Then Press [OK] To Save
Access > Prox Reader >
Access Group
MENU 1-6-2
0
Use Keys [] and [] keys or enter 1 - 8 (0 = No Access Group) To
Assign The Reader To An Access Group , Then Press [OK] To Save. Can
Only Be Assigned To One Access Group
Access > Prox Reader >
Reader Options MENU 1-6-3
1 All On Arming Allowed Y
2 Disarming Allowed Y
3 Badging Required N
4 Zero Exit Time N
5 Part On Badging Allowed N
6 Arm If Single Area User N
7 Reserved N
8 Reserved N
Use Keys [] and [] to scroll up and down the option list. With option
selected press ON / OFF key to enable or disable option. [] will display
to indicate option set. Press [OK] To Save when finished.
Are a Pro gramming
By default the Solution 16
plus
is configured for one area.
Examples given in this document are for Area 1 only. If the
system is configured for more than one area then you will
be prompted on the keypad to select the area you want to
work on.
Areas > Commands >
Area Status
MENU 2-0-0
Turn Area On/Off
MENU 2-0-1
Turn All Areas On
MENU 2-0-2
Turn All Areas Off
MENU 2-0-3
Move To Area
MENU 2-0-4
Chime On/Off
MENU 2-0-5
Chime Mode
MENU 2-0-6
Areas > Area Properties >
Area Name
MENU 2-1-0
A r e a 1 N a m e
Use [] and [] Keys To Scroll Cursor Left and Right. Use Keys [0]
– [9] + [#] and [•] To Toggle Characters + Enter [OK] To Save
Areas > Properties >
General Options MENU 2-1-1
1 Exit Time Restart N
2 Reset Alarm Memory On Disarm N
3 Duress Allowed Y
4 Acknowledge All Faults N
5 Single Button Arming Allowed - All On Y
6 Single Button Arming Allowed - Part On Y
7 Link To Common Area N
8 Single Button Part Off N
Use Keys [] and [] to scroll up and down the option list. With option
selected press ON / OFF key to enable or disable option. [] will display
to indicate option set. Press [OK] To Save when finished.
To Next Page
Loading...
Need help?
General
