Solution 16
plus
28
Bosch Security Systems 09/06 BLCC100R
Quick Start Guide
Comms > Dialler Reporting >
Burg Report Delay
MENU 5-4-6
0 0 0
SECONDS
Enter 0 – 255 seconds + [OK] To Program The Delay Time In Seconds
Before Reports Are Sent. 0 = No Delay
(*** System Wide Parameter ***)
Comms > Dialler Reporting >
Fire Report Delay
MENU 5-4-7
0 0 0
SECONDS
Enter 0 – 255 seconds + [OK] To Program The Delay Time In Seconds
Before Reports Are Sent. 0 = No Delay
(*** System Wide Parameter ***)
Comms > Comms Test >
Send Test Report
MENU 5-9-0
Comms > Comms Test >
Test Report Time
MENU 5-9-1
Test Time
02 : 00 am
HH MM
Use the [] and [] keys to move to the field then [] and [] to
change. Press [OK] to save or [MENU] to exit without saving.
Scroll through hours using the [] and [] to change
from am to pm.
Comms > Comms Test >
Test Report Period
MENU 5-9-2
0 = No Test Report
1
1 = Every Day
2 = Every Week
3 = Every Month
MENU 5-9-3 Programs The Interval Between Automatic Test Reports.
Use Keys [
] and [] keys or enter [0] to [3] + [OK] To Program.
(*** System Wide Parameter ***)
Comms > Comms Test >
Test Report Options MENU 5-9-3
1 Send Test Reports Only If No Other Report N
2 Send Test Reports On Siren Reset / Time Out Y
3 Reserved N
4 Reserved N
5 Reserved N
6 Reserved N
7 Reserved N
8 Reserved N
Use Keys [] and [] to scroll up and down the option list. With option
selected press ON / OFF key to enable or disable option. [] will display
to indicate option set. Press [OK] To Save when finished.
Comms > Comms Test >
Test Route
MENU 5-9-4
0 = Report Events To Log Only
1
1 = Report Events To Destination 1 + Log
2 = Report Events To Destination 2 + Log
3 = Report Events To Destination 1 & Destination 2 + Log
4 = Report Events To Destination 2 If Destination 1 Fails + Log
Use Keys [] and [] keys or enter 0 - 4 + [OK]. To Enter Single Option
Only. (*** System Wide Parameter ***)
Comms > Comms Test >
Dial Number Test
MENU 5-9-5
Use the option to test the system dialer to your mobile or other phone.
Enter the digits to dial and press OK. The system will call the number
entered. This function will stop after 30 seconds or by pressing OK.
Enter [0] – [9] For Telephone Digits.
Use [] and [] To Toggle Special Characters # and , (Pause)
Device Pro grammi ng
Devices > Commands >
LAN Status
MENU 6-0-0
LAN Secure
MENU 6-0-1
Devices > Keypads >
Keypad Volume
MENU 6-1-0
Keypad Contrast
MENU 6-1-1
Keypad Backlight
MENU 6-1-2
Devices > Keypads >
Home Area
MENU 6-1-3
1
Use Keys [] and [] keys or enter 1 - 4 Then Press [OK] To Set The
Home Area. This is the Area which will be diplayed on the keypad by
default.
All keypads must have a home area programmed
to work correctly.
Devices > Keypads >
General Options MENU 6-1-4
1 Keypad Extinguish N
2 Greeting On Arming Y
3 Greeting On Disarming Y
4 Enable Rear Tamper N
5 PIN To Change Area N
6 Home Area Only N
7 Report/Display Keypad Temperature Y
8 Display Area ICON Indicators N
Use Keys [] and [] to scroll up and down the option list. With option
selected press ON / OFF key to enable or disable option. [] will display
to indicate option set. Press [OK] To Save when finished.
To Next Page
Loading...
Need help?
General
