The stove previews the necessary air intake for the combustion on it back (40 mm diameter). It is important
not to block this air intake, and to respect the distance recommended from the walls and furnishings nearby.
It is recommended but not obligatory connecting the primary air intake of the stove to the exterior. Regarding
the material of the connection pipe, it is not necessary to be metallic, it could be made of another material
(PVC, aluminium, polyethylene, etc), note that for this line air will circulate with the outside ambiance
temperature.
6
66
6 STARTING
STARTINGSTARTING
STARTING
UP
UPUP
UP
The lightning of this type of devices is completely automatic therefore you must not introduce in the burn pot
any type of material for its lightning.
During the first lightning it may happen that the device has finished the lightning cycle and does not appear
the fire. If this happens the device goes on automatically to state of alert. This is due to the fact that the feeder
of the fuel is empty and needs a time to fill. To solve this problem light again the heater again until the fire
appears.
It is prohibited the use of all the liquid, such substances like, for
It is prohibited the use of all the liquid, such substances like, for It is prohibited the use of all the liquid, such substances like, for
It is prohibited the use of all the liquid, such substances like, for example, alcohol, gasoline, oil and similar. The
example, alcohol, gasoline, oil and similar. The example, alcohol, gasoline, oil and similar. The
example, alcohol, gasoline, oil and similar. The
use of the above mentioned substances will cause the loss of the guarantee.
use of the above mentioned substances will cause the loss of the guarantee.use of the above mentioned substances will cause the loss of the guarantee.
use of the above mentioned substances will cause the loss of the guarantee.
• During its lifetime, the product will be subject to alternating cycles of heating and cooling both
on a daily basis as well as cycles of intense use or total rest depending on the season.;
• Before fully settling in, the device must be subjected to several cycles of use so that the materials
and paintwork can settle in and bind flexibly;
• In particular it may be noticeable on first light
it may be noticeable on first lightit may be noticeable on first light
it may be noticeable on first lightning the stove that there is smell of hot metal and
ning the stove that there is smell of hot metal and ning the stove that there is smell of hot metal and
ning the stove that there is smell of hot metal and
fresh paint.
fresh paint.fresh paint.
fresh paint. During manufacture the paint has already been heat treated to extremely high
temperatures but before binding completely with the metal surface it needs to be run at
sustained temperatures of 200 degrees for long periods and on several occasions.
Therefore, it is important to adopt these small precautions in starting phase:
1. Keep the room well ventilated to avoid a build up of fumes.
2. For the first few lightings of the fire, take care not to overload the fire box with fuel and
preferably keep it lit for 6-10 hours continuously.
3. Repeat this procedure at least four or five times.
4. During the first few uses, nothing should be placed on the device or the paintwork, nor
During the first few uses, nothing should be placed on the device or the paintwork, nor During the first few uses, nothing should be placed on the device or the paintwork, nor
During the first few uses, nothing should be placed on the device or the paintwork, nor
should painted surf
should painted surfshould painted surf
should painted surfaces be touched whilst heating up.
aces be touched whilst heating up.aces be touched whilst heating up.
aces be touched whilst heating up.
5. Even after this initial phase of “running in” is complete, the appliance should be treated like car
engines i.e. avoid both overloading and overheating.
7
77
7 USUAL OPERATION
USUAL OPERATIONUSUAL OPERATION
USUAL OPERATION
As well as regulating the air intake, the draw on the flue will affect the rate of combustion and the heat
output of the device. A strong pull on the chimney will need a reduction on the draw to the fire, while a weak
pull will require extra attention to the setting of the air intake controls.
Check if the draw to the fire is correct by looking at the colour of smoke being emitted. It should be
transparent. If it is white, it means that the controls have not been set correctly or the used pellet is too wet. If,
on the other hand, the smoke is black or grey, it means that the fuel is not being completely burned and the
secondary air intake must be increased.
8
88
8 MAINTENANCE AND CARE
MAINTENANCE AND CAREMAINTENANCE AND CARE
MAINTENANCE AND CARE
The maintenance operations guarantee that the product works correctly during long time. If you don’t do it, it
can damage the device.
8.1
8.18.1
8.1
Burn pot
Burn potBurn pot
Burn pot
c
cc
cleaning
leaningleaning
leaning
The cleaning of the burn pot must be carried out every day.
• Extract the burn pot and to unblock the orifices with corresponding poker, which is given
together with the heater.
• Use a vacuum cleaner to eliminate the ash of the burn pot
• Vacuum the ash deposited in the accommodation of the burn pot.
To Next Page
Loading...