EasyManuals Logo

Brother HL-5450DN Technical Reference Guide

Brother HL-5450DN
517 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #148 background imageLoading...
Page #148 background image
CHAPTER 3 PCL5C - 12
4. COLOR GRAPHICS
4.1. Start Raster Transfer
Command
ESC*r#A (27)(42)(114)#(65) <1Bh><2Ah><72h>#<41h>
# = 0 * Prints the image from the left edge of the logical page.
= 1 Prints the image from the current cursor position.
= 2 Executes scaling. Prints the image from the left edge of the logical
page.
= 3 Executes scaling. Prints the images from the current cursor position.
* Default value = 0
This command signals the start of the transfer of raster image data to the printer.
The transfer of raster data to the printer continues until either an End Raster Transfer command is sent or a
command other than Send Raster Data, Set Compression Mode or Y-Offset is sent.
The source width and height are set by the Set Raster Area Width (ESC*r#S) and Set Raster Area Height
(ESC*r#T) commands. When the # value is 2 or 3, the data with these source width/height values is
enlarged or reduced to the width and height set by the Set Destination Raster Width and Set Destination
Raster Height commands. (Refer to the following sections.)
4.2. Set Destination Raster Width
Command
ESC*t#H (27)(42)(116)#(72) <1Bh><2Ah><74h>#<48h>
Range = 0 ~ 32767 (number of decipoints in 1/720")
Default value = 0
If value 2 or 3 is sent with the Start Raster Transfer command and graphic scaling is set, this command sets
the destination width.
Values outside the range are invalid.
If the setting is 0 or is omitted, this command uses the same width as the source width.
If the specified width is wider than the page, drawings are clipped by the right physical page boundary.
The scaling factor is dealt with correctly.
4.3. Set Destination Raster Height
Command
ESC*t#V (27)(42)(116)#(86) <1Bh><2Ah><70h>#<56h>
Range = 0 ~ 32767 (number of decipoints in 1/720")
Default value = 0
If value 2 or 3 is sent with the Start Raster Transfer command and graphic scaling is set, this command sets
the destination height.
Values outside the range are invalid.
If the setting is 0 or is omitted, this command uses the same height as the source height.
If the specified height is longer than the page, drawings are clipped by the bottom of physical page
boundary. The scaling factor is dealt with correctly.

Table of Contents

Other manuals for Brother HL-5450DN

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Brother HL-5450DN and is the answer not in the manual?

Brother HL-5450DN Specifications

General IconGeneral
ColorNo
N-up printing2, 4, 9, 16, 25
Duplex printingYes
Print technologyLaser
Maximum resolution2400 x 600 DPI
Time to first page (black, normal)8.5 s
Print speed (black, normal quality, A4/US Letter)38 ppm
Duplex print speed (black, normal quality, A4/US Letter)9 ppm
Maximum duty cycle- pages per month
Recommended duty cycle1000 - 3500 pages per month
Number of print cartridges1
Memory typeDDR2
Processor familyStar Sapphire
Maximum internal memory320 MB
Sound power level (standby)34 dB
Sound pressure level (printing)59 dB
Sound pressure level (quiet mode)54 dB
Total input capacity250 sheets
Total output capacity150 sheets
Maximum input capacity800 sheets
Total number of input trays2
Multi-Purpose tray input capacity50 sheets
Custom media width76.2 - 215.9 mm
Maximum print size216 x 356 mm
Custom media length127 - 355.6 mm
Paper tray media typesPlain paper, Recycled paper
Paper tray media weight60 - 105 g/m²
Non-ISO print media sizesLetter
ISO A-series sizes (A0...A9)A4, A5, A6
ISO B-series sizes (B0...B9)B5, B6
Multi-purpose tray media typesBond paper, Envelopes, Heavyweight paper, Labels, Plain paper, Recycled paper
Maximum ISO A-series paper sizeA4
Multi-Purpose Tray media weight60 - 163 g/m²
Standard interfacesEthernet, USB 2.0
USB 2.0 ports quantityUSB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
AC input voltage220 - 240 V
AC input frequency50 - 60 Hz
Power consumption (off)0.41 W
Power consumption (standby)4.7 W
Power consumption (printing)665 W
Power consumption (PowerSave)0.6 W
Package weight11.900 g
Sustainability certificatesENERGY STAR
Weight and Dimensions IconWeight and Dimensions
Dimensions (WxDxH)371 x 384 x 245 mm

Related product manuals